Where Can You Install The Excel RV Tankless Water Heater

Question

Question:

If your old hot water heater is in the bedroom under the bed. The new Excel Vent-Free Tankless Propane Water Heater says not to install bedroom or bathroom. So the question is where do you put this to be out of the place or hidden and without having to run a whole new gas line? Any please please!!

asked by: Thomas

0

Expert Reply:

The Excel RV Tankless Water Heater # EX93FR could be installed in an exterior storage compartment nearby so that you could just hook on an extension to your current hard line and run it to the storage compartment. If you have a travel trailer there's typically a hull towards the front of the trailer just past the master bed.

You would need some copper hard line, a flaring tool, and a male and female flare fitting to connect the extension to the current supply line. You'll also want a tubing bender tool to navigate the line over to your compartment bay. Once you have the line over to the unit you'll need another male flare fitting to connect to the unit.

You'll also obviously have to move you water lines to over the unit as well. All tools and parts can be picked up at your local hardware store.

expert reply by: Kevin C

0

Answer 1

Because the Furrion RV Tankless Water Heater, model #FR93FR that you linked to, and other similar models, are most commonly mounted in compartments with exterior access doors that are not heated, the manufacturer recommends that they be winterized…

view full answer...

Answer 2

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 3

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 4

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 5

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 6

Assuming your Sprinter has the factory tow package with the 7-way at the rear bumper, in addition to the #RED24FR Redarc Tow-Pro Liberty Brake Controller, you'll also need the #3063-P wiring harness and the #331-TPH-017. The connector to install…

view full answer...

Answer 7

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 8

We have a really great kit that comes with everything you'd need to convert your 2021 Vanleigh Pinecrest 335RLP from tandem 6k drum brakes to electric over hydraulic disc brakes with the HydraStar Disc Brake Kit w/ Actuator for Triple Axle…

view full answer...

Answer 9

From our experiences the Harbor Freight trailers like yours have a hub bore that requires a cap or Bearing Buddy that measures 2.047 inches like the #BB2047 you referenced. We don't have a standard cap that fits this size so the Bearing Buddy is…

view full answer...

Answer 10

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 11

The installation instructions for this product are recommended for individuals who have experience winding torsion springs. If you have not worked with a torsion spring system before, we recommend contacting a local garage door company to install…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Where Can You Install The Excel RV Tankless Water Heater

Product Page this Question was Asked From

Continue Researching