Do You Carry The Dexter 006-109-00 Lug Nut?

Question

Question:

Do you carry dexter lug nuts Pn# 006-109-00 Or something equivalent

asked by: Carl R

0

Expert Reply:

We do carry the Trailer Wheel Lug Nut # 6-109. This is the same as the Dexter 006-109-00.

expert reply by: Bud M

0

Answer 1

The trailer tire and wheel combo to fit your 10K Dexter axle would be the Taskmaster Provider ST235/85R16 Trailer Tire with 16" Vesper Silver Dual Wheel, #TA45FR. This wheel can be used as either the inner or outer wheel of a dual-wheel…

view full answer...

Answer 2

As long as your dual wheel has a flat surface where the Flange Wheel Nut #95188 would rest against, like what the Dexstar Dual Wheel #AM20790 has, then you would use this flange wheel nut in the place of a nut with a 90 degree cone. Attached is a…

view full answer...

Answer 3

The retaining tab on the Wheel Retaining Ring #33-52-1 will need to be installed facing out so that the taper of the ring matches the lug nuts. Attached is a product overview video for you to check out as well.

view full answer...

Answer 4

The wheel retainer ring that is included in certain hub assemblies like the Dexter #8-430-5UC3 that you referenced will be installed on dual wheels when tapered coned lug nuts like #6-109 are used instead of flange wheel nuts. It essentially allows…

view full answer...

Answer 5

If the Dexter actuator, #K71-651, is not building pressure then according to Dexter the unit could be defective. If the unit is wiring up correctly, see diagram, and you ahve run through all of the troubleshooting procedures below and it is still…

view full answer...

Answer 6

The torque for the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility #8-174-5UC3 is not specified by the manufacturer. For 9/16 inch studs, the typical lug nut torque will be 120-140 ft lbs based on most…

view full answer...

Answer 7

I spoke to Dexter and they said there is a bit of a process for installing the spindle nut properly. 1. You will need to thread on the inner nut, rotate the hub, then tighten the nut to 100 foot pounds. 2. Loosen the nut to remove the torque, making…

view full answer...

Answer 8

The Replacement O-Ring for Dexter Axle 10K and 12K Disc Brakes part #010-062-00 install on the brake caliper guide bolts between the brake pads as shown in the photo below.

view full answer...

Answer 9

A caliper like the Disc Brake Caliper for Dexter 10K & 12K Hydraulic Disc Brakes #BP18-045 uses four of the #010-062-00 O-rings. These are designed to go onto the brake caliper guide bolts, two for each bolt. If you need additional parts we have…

view full answer...

Answer 10

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 11

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 12

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Do You Carry The Dexter 006-109-00 Lug Nut?

Product Page this Question was Asked From

Continue Researching