How To Stop A-Frame Jack From Scrapping Ground While Going Over Bumps
Question:
Is this Jack available with a side handle or can I use a drill adapter to crank it. I do not have clearance on my trailer for a top handle crank. I have about 3 inches between the Jack stand and the tip of the V nose. Thx.
asked by: Wayne
Helpful Expert Reply:
I do have an option for you but I don't have any way to reduce the ground clearance of your existing a-frame jack . That said, what you can do to fix this issue is replace your existing jack with the Ultimate Trailer Jack part # 322-RDJ-2K. The Ultimate Trailer Jack can be adjusted so that the foot is even with the bottom of the frame so there's no more worrying about bottoming out. This also makes it much faster to raise the trailer as the jack acts as a drop leg.
Products Referenced in This Question
Square A-Frame Jack w/ Footplate - Drop Leg - Sidewind - 28-3/4" Lift - 3,000 lbs
- Trailer Jack
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- A-Frame Jack
- Leveling Jacks
- Tongue Jacks
- Steel
- 2001 - 3000 lbs
- Sidewind Jack
- 29 Inch Lift
- Bolt-On
- With Rectangle Foot
- etrailer
more information >
Product Page this Question was Asked From
Ultimate Trailer Jack - A-Frame - Topwind - 27-1/2" Lift - 2,000 lbs
- Trailer Jack
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- A-Frame Jack
- Leveling Jacks
- Tongue Jacks
- Steel
- 1001 - 2000 lbs
- Topwind Jack
- 28 Inch Lift
- Bolt-On
- Weld-On
- With Rectangle Foot
- Ultimate Jack
more information >
Continue Researching
- Shop: Ultimate Trailer Jack - A-Frame - Topwind - 27-1/2" Lift - 2,000 lbs
- Shop: SnapPad EQ Plus Jack Pads for Equalizer Leveling System w 10" Round and 10" Octagon Feet
- Shop: SnapPad EQ Octagon Jack Pads for Equalizer Leveling System w 10" Octagon Jack Feet- Qty 4
- Shop: Square A-Frame Jack w/ Footplate - Drop Leg - Sidewind - 28-3/4" Lift - 3,000 lbs
- Q&A: How To Stop A-Frame Trailer Tongue Jack from Bottoming Out
- Shop: ClearPlus Sentinel Windshield Wiper Blade - Frame Style - 22" - Qty 1
- Shop: Hopkins Endurance 5th Wheel/Gooseneck 90-Degree Wiring Harness w/ 7-Pole and 4-Pole Connector
- Video: Review of CURT Wheel Chocks - Wheel Chock Set with Trailer Frame Mounting Brackets - C62FV
- Shop: Round A-Frame Trailer Jack - Topwind - 14-1/4" Lift - 2,000 lbs
- Video: Review of Ultimate Jack Trailer Jack - A-Frame Jack - 322-RDJ-2K
- Video: etrailer Square A-Frame Jack with Footplate Review
- Video: Ultimate Trailer Jack A-Frame Topwind Jack Review
- Q&A: Dimensions Of The MORryde Sliding Tray For RV Cargo Compartments # MR87FR
- Q&A: Safety Chain Weight Ratings and Dimensions
- Search Results: a frame jack
- Search Results: chocks
- Article: How to Measure for Trailer Hitch Drop
- Q&A: How to Select a Ball Mount or Draw Bar with the Correct Ball Hole Size 1-1/4"
- Q&A: Recommendation for Allowing Clearance To Open Truck Tailgate When Attached To A-Frame Trailer Jack
- Video: etrailer and Ram Jacks Drop Leg Review
- Video: Bulldog Trailer Jack - A-Frame Jack - BD1550101344 Review
- Q&A: Do All A-Frame Trailer Jacks Use the Same Mounting Pattern and Center Hole
- Q&A: Low Profile Trailer Jack to Fit Under Tailgate of Truck
- Search Results: 5/8 pin
- Video: SumoSprings Solo Front Helper Springs Installation - 2017 Ford E-Series Cutaway
- Article: Can You Flat Tow a Ford Ranger
- Search Results: optronics clearance light
- Search Results: fender lights
- Search Results: torsion axel for trailer
- Search Results: drop axle
Wayne M.
12/12/2022
Is this Jack available with a side handle or can I use a drill adapter to crank it. I do not have clearance on my trailer for a top handle crank. I have about 3 inches between the Jack stand and the tip of the V nose. Thx.