Can Demco A-Frame Trailer Coupler be Used on Car Hauler Trailer

Question

Question:

DM14793-52, would this product be ok for use on a car hauler trailer?

asked by: Brent

0

Expert Reply:

Yes; your car hauler trailer has to have an A-frame and be within the correct weight rating, but if so you can definitely use the Demco A-Frame Trailer Coupler # DM14793-52.

The # DM14793-52 has a 10,000 lb capacity so that's the most your loaded trailer can be, but otherwise this will certainly work for a car hauler trailer.

expert reply by: Kyle S

0

Answer 1

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 2

The great thing about Bearing Buddy like part #BB1781 is that when you add grease to your system with the included fitting, it will move the spring-loaded piston outward and allow grease to seep around the edges to keep from damaging the seal. You…

view full answer...

Answer 3

It is possible to over-fill a hub that has a Bearing Buddy bearing protector such as #BB1781. The convenience of easy filling through the zerk fitting can often mean we can be tempted to keep adding more grease. ("If a little is good, then more…

view full answer...

Answer 4

The Lippert Components Spare Tire Winch with Offset Cable #LC159056 requires the handle #LC119226 to crank up and down.

view full answer...

Answer 5

The Replacement Crank Extension for Lippert Components Spare Tire Winch Assemblies #LC1315411, which is a replacement for Lippert Components Spare Tire Winch with Offset Cable #LC159056, has an inside diameter of 0.50 inches and the hex has a 0.75…

view full answer...

Answer 6

To raise and lower the Lippert Spare Tire Winch with Offset Cable #LC159056 what you need is the replacement manual crank handle part #LC119226.

view full answer...

Answer 7

There are going to be two parts to the handle that you will need to operate the Lippert Components Spare Tire Winch part #LC159056. The first of which is the intermediate shaft or what Lippert calls a Crank Extension part #LC1315411. This will be…

view full answer...

Answer 8

The crank handle for the Lippert Components Spare Tire Winch with Offset Cable item #LC159056, is Replacement Crank Extension for Lippert Spare Tire Winch Assemblies - 35-1/2" item #LC1315411. The Spare Tire Winch item #LC159056 has a 1/2-inch…

view full answer...

Answer 9

The Lippert Components Spare Tire Winch with Offset Cable #LC159056 will not have any locking or hold mechanism short of being completely reeled in. I spoke to my tech contact at Lippert who has this on his truck and he said you just crank it up…

view full answer...

Answer 10

The tires on your trailer should not come off the ground while leveling. It sounds like you just need to reset the zero point. In order to do this you will need to follow the steps I have attached for you below and in the photo. If this does not fix…

view full answer...

Answer 11

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 12

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Can Demco A-Frame Trailer Coupler be Used on Car Hauler Trailer

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching