Where to Install Konig Tire Chains At On a 2019 Mazda CX-5 with P225/55R19 Tires

Question

Question:

Are these chains stalled in the front or rear? Thank You

asked by: Richard J

0

Expert Reply:

The Konig Tire Chains part # TH01594247 which are a fit for a 2019 Mazda CX-5 with P225/55R19 tires will need to be installed on the front axle only per the owner's manual.

expert reply by: Conner L

0

Answer 1

When using a single set of tire chains on a vehicle that is 4 wheel drive or all wheel drive you want to install the chains on the primary drive axle. Typically this will be listed in the owner's manual. But for a 4WD drive vehicle the axle to…

view full answer...

Answer 2

The correct Konig Self-Tensioning Snow Tire Chains for 225/55-19 tires is size 247 part #TH01594247. The correct Konig Self-Tensioning Snow Tire Chains for 225/65-17 tires is size 245 part #TH01594245. The two are not interchangeable unfortunately.

view full answer...

Answer 3

According to the owner's manual, Honda recommends installing chains on the front tires only. The manual states that because of the limited clearance to the inside of the tire, cable-type chains should be used. The cables needed will depend on the…

view full answer...

Answer 4

If your 2017 Mazda CX-5 is equipped with 225/55-19 size tires then the Konig Standard Snow Tire Chains #TH01571247 that you referenced will fit and work perfectly. I checked the online version of the owner's manual for your Mazda CX-5 and the…

view full answer...

Answer 5

Your 2016 owners manual online says to use snow chains only on the front wheels. There are two different size wheels that come with your 2016 Mazda CX-5, so there are two different size chains I will recommend. They can be used on regular, standard…

view full answer...

Answer 6

You ask a very good question. Tire chains that are rated as S-Class compatible are suitable for use on passenger vehicles that have limited clearance in the wheel wells. Unlike a vehicle like a pickup truck that generally has a good bit of room…

view full answer...

Answer 7

The wheel protectors that come with the Konig Chains part #TH01594247 are optional but I strongly recommend using them if you value your wheels! You'll just need to put them in the best locations that will protect the wheels. There isn't a…

view full answer...

Answer 8

If you imagine that you are on the side of the road, in the cold, wet snow, with other vehicles going by you can probably guess that you would want the chains that are going to be the easiest to install. Something that you won't have to put on,…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...

Answer 12

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Where to Install Konig Tire Chains At On a 2019 Mazda CX-5 with P225/55R19 Tires

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching