What Axle Capacity is the Replacement Trailer Brake Magnet for Dexter Electric Brake BP01-225 For

Question

Question:

Dexter magnet kit part number K71-125-00 is for what weight Dexter axle?

asked by: Richard R

1

Helpful Expert Reply:

The Replacement Trailer Brake Magnet for Dexter Electric Brake Assemblies part # BP01-225 is designed for a 7,000 lb trailer axle.

expert reply by: Conner L

1

Answer 1

You said you checked the brake magnets. When inspecting them did you notice if the windings inside the magnets are showing? If so this is most likely the reason that the short is showing up on the controller when the vehicle is moving. This would…

view full answer...

Answer 2

I can certainly help you find the replacement brake shoe and brake magnets for your Dexter brake assemblies on your 2014 Forest River. We have different part numbers for the replacement parts you listed, but they are the correct parts for your brake…

view full answer...

Answer 3

As you may have already found, 5200 lb, 6000 lb and 7000 lb axles can all use the same components including inner/outer bearings, hubs and brakes. Here are some other things they share in common: Dexter 5200 lb Regular Duty Axle - 0.180 inch tube…

view full answer...

Answer 4

The replacement magnet, #BP01-225, fits several different brake assemblies. it fits Dexter 10 x 2-1/4 inch assemblies, Dexter 12 x 2 manual assemblies and 12 x 2 Nev-R-Adjust assemblies, 7K axles. For a brake magnet with a red wire we have #BP01-285.…

view full answer...

Answer 5

The difference between these two parts comes down to the size of the brake assembly and hubs that are on your axles. The #AKBRKR-M10 that has green wires are designed for 10" electric brake assemblies, where the #BP01-225 are designed for…

view full answer...

Answer 6

First, a 5,200 pound axle is a de-rated 6,000 pound axle so they take many of the same parts. Some 7,000 pound axles also take the same size parts. The difference is the size or ability of the magnets. Sometimes you will see the same type of magnet…

view full answer...

Answer 7

I currently have three diffrent self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes which are attached for you below. eTrailer Electric Trailer Brake Kit part #AKEBRK-35-SA (3,500 Axles) Dexter…

view full answer...

Answer 8

Get the hub off and get me either the diameter of the spindles where the bearings ride or the numbers stamped on the bearings. If there is a set of Dexter brake assemblies used currently there's a very good chance you have a standard hub that…

view full answer...

Answer 9

The "Trailer Disconnected" error message on the dash with a factory brake controller is usually related to an issue with the blue brake output wire that runs from the brake controller to the 7-Way connector. The fact that the issue remains…

view full answer...

Answer 10

Given the round magnet, it sounds like you have old Hayes 10 x 2-1/4 brake assemblies that have been obsolete for several years, so replacement parts aren't available any longer. Your best bet would be to replace your existing brake assemblies…

view full answer...

Answer 11

Yes they are! The Dexter Electric Trailer Brake Assembly #23-180 (Left Hand) and #23-181 (Right Hand) are made in the USA; the accompanying photo is from one of these assemblies with the "Made in U.S.A." sticker on it. These electric brake…

view full answer...

Answer 12

The KB10E-06 #AKBRKR-M10 and the KB12E-06 #AKBRKR-M12 are similar magnet designs but they are intended for different applications/sizes of brake assemblies. The #AKBRKR-M12 is for 12 inch assemblies and the #AKBRKR-M10 is for 10. The temptation is to…

view full answer...

What Axle Capacity is the Replacement Trailer Brake Magnet for Dexter Electric Brake BP01-225 For

Product Page this Question was Asked From

Continue Researching