Bearing Kit for Dexter D35 Trailer Axle

Question

Question:

Hi I need to replace the bearings on a dexter d35 axel for a travel trailer not sure of the part number I uploaded some info for the axel thanks alot.

asked by: Feuaz K

0

Expert Reply:

The Dexter D35 axle is a 3,500 lb trailer axle so for a bearing kit you would want the part # BK2-100 that you referenced.

expert reply by: Jameson C

0

Dexter D35 Trailer Axle
(click to enlarge)

Answer 1

If the diameter of the spindle where the seal rides is 1.5 inch then the bearing kit part #BK2-100 is correct and you'd have what is most likely a 3,500 lb axle.

view full answer...

Answer 2

Though there can be some variations, the #GS-2250DL (10-36) seal would lead me to believe you have a 5,200 pound or 6,000 pound axle. Especially with a 6 on 5 1/2 bolt pattern on the hub. It would not hurt to pull one of said hubs off to verify…

view full answer...

Answer 3

I have attached the wiring diagram for the Titan BrakeRite EHB Electric-Hydraulic Actuator #T4822500 that you referenced. This particular actuator is designed for use with hydraulic drum brakes and features 1,000 psi of hydraulic pressure. I have…

view full answer...

Answer 4

Dexter 3,500 lb axles are very common. They might be the most common axle found on trailers actually. Because of that we know that they bearing kit you need is the #BK2-100 which includes the correct bearings and seal.

view full answer...

Answer 5

It looks like Trailer Hub and Drum Assembly - 5,200-lb Axles - 6 on 5-1/2 Item #8-201-5UC3 could be the right replacement for you. You can check the bearing numbers if you still have the bearings. If they are 25580 for the inner and LM67048 then…

view full answer...

Answer 6

Weight distribution works to distribute the tongue weight of a trailer up to the front axle of the tow vehicle so that it will sit more level and handle/brake better. That being said the systems do not "reduce" tongue weight or allow you to…

view full answer...

Answer 7

You can verify that the 10-19 grease seal included in Bearing Kit #BK2-100 is the correct one for your spindles by taking two measurements. First you want to measure the rear hub bore where the seal is inserted. The seal's outer diameter needs to…

view full answer...

Answer 8

The standard 3,500 lb axle uses the Hub Bearing Kit #BK2-100 which is for a #84 spindle. If your axle is a 1990 or newer then you likely need these parts but if it's older then I'll need you to measure your spindle to make sure we can get you…

view full answer...

Answer 9

The Bearing Kit #BK2-100 is the one most likely to fit your Barrett trailer. You will want to confirm this is the correct kit by comparing it with your current bearings or measuring your spindle and hub. This will include a grease seal if you are…

view full answer...

Answer 10

There are going to be 2 ways to find out what size spindle is on your Dexter 3500lb axles under your car trailer. First every Dexter axle manufactured after April 2001 will have a serial number stamped on the rear of the axle tube near the passenger…

view full answer...

Answer 11

You can select your new hubs by matching up your axle weight rating, wheel bolt pattern and the bearings used in your current hubs. Based on my research your hubs are 10 x 2-1/4-inches, are from a 3500-lb axle and have the 5-on-4-1/2 bolt pattern. If…

view full answer...

Answer 12

The 052-003-00 number on your current shock is the part number from Dexter Axle. We don't carry the direct replacement but if the specs match for the Lippert Standard Replacement Shock #LC283271 and the axle this is being applied to is a…

view full answer...

Bearing Kit for Dexter D35 Trailer Axle

Product Page this Question was Asked From

Continue Researching