Do L68110 and L68111 Races Work With L68149 Bearing

Question

Question:

Hello! Again! This kit uses inner bearing cup part # L68111. Dexter says L68110. That bearing is for under 3500lbs. Should I use your kit wirh the L68111inner bearing race? Thank you! Again!

asked by: Larry M

0

Expert Reply:

The Race # L68111 and the Race # L68110 are both for the # L68149 bearing so if Dexter Axle is saying you need the slightly smaller one I'd go with that instead of the one that comes with the Bearing Kit # BK2-100.

expert reply by: Jon G

0

Answer 1

Yes, if the retainer nut is in good shape you can use all of the other components of the Hub Bearing Kit for Lippert, Dexter, and Al-Ko Axles - 3,500 lb with #84 Spindle #BK2-100 and not worry about the tang washer and cotter pin. If the spindle…

view full answer...

Answer 2

The standard 3,500 lb axle uses the Hub Bearing Kit #BK2-100 which is for a #84 spindle. If your axle is a 1990 or newer then you likely need these parts but if it's older then I'll need you to measure your spindle to make sure we can…

view full answer...

Answer 3

Part #168233, appears to be a close match to your existing grease seal with 2-5/16" (2.3125) OD and 1-11/16" (1.6875) ID. It has an ID of 1.688", OD of 2.332" and a thickness of 0.38". Although I wasn't able to cross…

view full answer...

Answer 4

Yes, the 7-Piece Installation Set for Bearings, Races, and Seals #PTW83020 that you referenced will work with the races you mentioned as they are very common races found on trailer axles which is what this kit is designed to fit.

view full answer...

Answer 5

You are always going to end up burning a seal when you work on a hub or change bearings. Anything that requires removing the seal. Its because they go in so tight. With an EZ lube axle you are going to want a double lip seal so your instincts were…

view full answer...

Answer 6

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 9

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 10

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 11

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 12

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Do L68110 and L68111 Races Work With L68149 Bearing

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching