Replacement Spring Bar Release Clip for Fastway e2 Weight Distribution System

Question

Question:

I have a E2 trailer Hitch Round Bar for my Cougar 1/2 ton 23MLS and Ram 1500 Truck. There is a small retractable pin on the hitch Ball component that locks in the round bar so that you can move the bar to the mechanism on the trailer to hold the bar in place. The pull back pin which appears to be held on and in place by two small friction rivets has come off. The friction rivel has come out and that light weight aluminum strip holding the pin is gone. Do you carry replacements for this pin?

asked by: Jerry H

0

Expert Reply:

Sounds like you are looking for the Replacement Spring-Bar Release Clip for Fastway e2 Weight Distribution Systems with Round Bars # FA94-02-1059 which is the correct release clip for the Fastway e2 round bar weight distribution systems.

expert reply by: Jameson C

0

Answer 1

Reese does not offer the spring bar retainer clips like you have referenced. The really good news is that you can use either the Replacement Spring-Bar Release Clip #FA94-02-1059 or Curt #17109. These clips will work as replacements for the hitch you…

view full answer...

Answer 2

We currently have the Spring Bar Retainers from Curt #17109 and Fastway #FA94-02-1059.

view full answer...

Answer 3

We have a few different clip options that are possible fits for your Weight Distribution (WD) system. Fastway WD - FA94-02-1059 Curt WD - 17109 From the picture that you sent me, I believe that the Curt clips #17109 are the correct replacement clips…

view full answer...

Answer 4

As far as I know this is not a common problem, and not something that we have had reported as an issue for the #FA94-00-1000. It is important to make sure that everything is secure when installing the weight distribution hitch. The spring bars should…

view full answer...

Answer 5

It sounds as if you're needing the spring bar retainer clip kit. If you have the Curt or a Reese Round Bar system, use #17109 which includes 2 clips, 2 lock pins and two drive-in rivets. The exact kit needed will depend on which…

view full answer...

Answer 6

First you have to get the lower screw out of the head of the system. Since the screws don't have a slot or Philips head on them you'll have to pry them out some have to use a chisel. Once they are out you'll slide the clip down so that it…

view full answer...

Answer 7

Sounds like you have a Fastway E2 weight distribution system and need new release clips to replace lost ones. For that you'd want the part #FA94-02-1059.

view full answer...

Answer 8

It sounds like you might need the clips that hold your round spring bars in the head unit. If you have a Fastway e2 system then their Replacement Spring-Bar Release Clips #FA94-02-1059 are the correct part. If you have a Curt system use their part…

view full answer...

Answer 9

Brent, to remove the Replacement Spring-Bar Release Clip for Fastway e2 Weight Distribution Systems with Round Bars #FA94-02-1059 you are going to need to start by getting the lower screw out of the clip which you're going to need to pry out…

view full answer...

Answer 10

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 11

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 12

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Replacement Spring Bar Release Clip for Fastway e2 Weight Distribution System

Product Page this Question was Asked From

Continue Researching