Replacement Spring Bar Retainer Clips for Weight Distribution System

Question

Question:

I was wondering if I can send you pictures of a hitch setup and if you could tell me what I need to repair it? The devices that retain the round bars need replaced. 1 fell off, the other is barely hanging on. I have pictures of the one that is still there. Please let me know what you can do to help.

asked by: Robert M

0

Expert Reply:

It sounds like you might need the clips that hold your round spring bars in the head unit. If you have a Fastway e2 system then their Replacement Spring-Bar Release Clips # FA94-02-1059 are the correct part. If you have a Curt system use their part # 17109.

Yes, you can certainly send us photos of your weight distribution hitch. You can just reply to this email with your photos and hitch brand information.

expert reply by: Adam R

0

Answer 1

Reese does not offer the spring bar retainer clips like you have referenced. The really good news is that you can use either the Replacement Spring-Bar Release Clip #FA94-02-1059 or Curt #17109. These clips will work as replacements for the hitch you…

view full answer...

Answer 2

Sounds like you have a Fastway E2 weight distribution system and need new release clips to replace lost ones. For that you'd want the part #FA94-02-1059.

view full answer...

Answer 3

We have a few different clip options that are possible fits for your Weight Distribution (WD) system. Fastway WD - FA94-02-1059 Curt WD - 17109 From the picture that you sent me, I believe that the Curt clips #17109 are the correct replacement clips…

view full answer...

Answer 4

It sounds as if you're needing the spring bar retainer clip kit. If you have the Curt or a Reese Round Bar system, use #17109 which includes 2 clips, 2 lock pins and two drive-in rivets. The exact kit needed will depend on which…

view full answer...

Answer 5

Yes, the Curt spring bar retainer package #17109 will fit Curt round bar weight distribution systems such as 17002 that you have. The kit comes with e2 clips, 2 pins, and 2 rivets.

view full answer...

Answer 6

The BrakeBuddy Towed Vehicle Battery Charge Kit part #BB54FR comes with a the Brake Buddy Select 3 Portable Supplemental Braking System part #HM39524. I have attached a wiring diagram of how this is setup with the Brake Buddy.

view full answer...

Answer 7

Sounds like you are looking for the Replacement Spring-Bar Release Clip for Fastway e2 Weight Distribution Systems with Round Bars #FA94-02-1059 which is the correct release clip for the Fastway e2 round bar weight distribution systems.

view full answer...

Answer 8

We currently have the Spring Bar Retainers from Curt #17109 and Fastway #FA94-02-1059.

view full answer...

Answer 9

Brent, to remove the Replacement Spring-Bar Release Clip for Fastway e2 Weight Distribution Systems with Round Bars #FA94-02-1059 you are going to need to start by getting the lower screw out of the clip which you're going to need to pry out…

view full answer...

Answer 10

As far as I know this is not a common problem, and not something that we have had reported as an issue for the #FA94-00-1000. It is important to make sure that everything is secure when installing the weight distribution hitch. The spring bars should…

view full answer...

Answer 11

When installing the included rivets from the Curt Spring Bar Retainer Package #17109 referenced in your question, you will not need any special tools to insert the new rivet/set key. The new set key (which likely has a slightly different design than…

view full answer...

Answer 12

To remove the retaining clips #17109 on a Curt weight distribution system with round bars you would first remove the bottom screws holding them on. Then you would push the clips up so the wider part of the hole can slip off the top pin. The top pin…

view full answer...

Replacement Spring Bar Retainer Clips for Weight Distribution System

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching