Wiring Voyager RV Camera Monitor For Use On Bobcat With Single Rear Camera

Question

Question:

I am hooking up a voyager back up camera on my bobcat. If I want the camera on when the key is turned on do I hook both the power and the trigger wire to keyed power?

asked by: Steve

0

Expert Reply:

When wiring up the Voyager RV Backup Camera Monitor # VOM719WP with a Camera # VGR84VR you will only need to connect the power wire to your ignition source. The trigger wires are designed to activate separate cameras using turn signals or reverse lights. Since you will only have one camera it will remain on the whole time without a trigger wire needed.

expert reply by: Bud M

0

Answer 1

The Voyager RV Backup Camera w/ Night Vision #VGR84VR is compatible with your VOM74 monitor with a Voyager DIN to ASA Monitor Cable Adapter #VGR54FR.

view full answer...

Answer 2

Absolutely! On the diagram that you mentioned, which I have attached for reference, the wire numbers are as follows: 1. Red (power +) 2. Yellow (Left) 3. Brown (Right) 4. Blue (Back/Rear) 5. Black (Ground) I have also attached the complete…

view full answer...

Answer 3

I just spoke with my rep at Voyager. The replacement monitor for the Voyager AOM 711 is going to be the Voyager RV LCD Observation Monitor - 7" Screen - 3 Video Inputs item #VO34FR.

view full answer...

Answer 4

In order to add the grid lines to your Voyager RV Backup Camera w/ Night Vision - Rear Mount #VGR84VR you are going to need to get into the menu screen on your monitor like #VO34FR, and through the settings you'll just need to toggle the marker…

view full answer...

Answer 5

The Voyager RV Backup Camera Monitor #VOM719WP could realistically be mounted in the dash, but you would have to come up with a way to mount it and run the wires yourself since there is no kit or mount designed for this. Typically this is mounted…

view full answer...

Answer 6

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 7

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 8

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 9

The Tekonsha OEM Vehicle Wiring Harness #22121 that you referenced includes all the wiring and parts necessary to install a fully functional 7-Way connector and trailer brake controller. The included brake controller harness is compatible with and…

view full answer...

Answer 10

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 11

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 12

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Wiring Voyager RV Camera Monitor For Use On Bobcat With Single Rear Camera

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching