What All Is Included In The Electric Trailer Brake Kit # AKEBRK-2

Question

Question:

Does the AKEBRK-2 set include the drums?

asked by: Robert S

0

Expert Reply:

The Electric Trailer Brake Kit # AKEBRK-2 comes with one left and one right brake assembly and included mounting hardware. The drums are not included. I would need to know what your inner and outer bearing numbers are on your current axle and I will be able to tell you what you need.

The nuts and lock washers # BRKH7 are sold separately. These brakes will work with 10 inch 12 inch and 13 inch wheels, and have an axle rating of 2,000 pounds.

I attached a review video link below.

expert reply by: Noah E

0

Answer 1

I attached a picture of a 4-bolt mounting flange like what the brake assembly part #AKEBRK-2 you referenced is designed to attach to. This is a standard dimension so I would be shocked if the flange on yours was different.

view full answer...

Answer 2

I do have some options for you but we don't know what parts a Jayco Swift 145RB uses so you'll have to do some legwork to get what you need. I am not sure if you're looking to add brakes or replace existing but I do know the…

view full answer...

Answer 3

In order to choose the correct electric brake assemblies for your 1994 Fleetwood Mallard, you will want to determine a couple of things. You will first want to determine the axle capacity on your trailer. This should be listed on a plate located…

view full answer...

Answer 4

The Electric Trailer Brake Kit - 7" - Left and Right Hand Assemblies #AKEBRK-2 are just the electric drum brakes for 2,000lb axles and do not include drums. They are designed for a 4 bolt mounting flange bolt pattern and fit most standard…

view full answer...

Answer 5

Based on your description of the issue you are having, it sounds like you might have the brake adjusted too tightly on the driver side. To make sure that the Dexter Electric Trailer Brake Kit #23-47-48 you installed on your camper are adjusted…

view full answer...

Answer 6

What we refer to as part #23-47-48 is a kit we assemble that includes the Dexter K23-047 and K23-048. They are the same exact parts, we're just selling them together as a single part number. They would be an exact replacement for the existing…

view full answer...

Answer 7

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 10

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 11

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...