Mounting Hole Spacing on the Sliding Under Platform Pontoon Boat Ladder

Question

Question:

Hello, what is the measurements between the bolts? Im trying to match this up to replace my OEM yamaha transom ladder. It looks identical, but Im worried about the mounting points.

asked by: Clint W

0

Expert Reply:

The Sliding Under Platform Pontoon Boat Ladder # 315-FOG3 has mounting hole spacing of:

- 1-13/16" between the holes closest together on the same side and end

- 6-1/4" between the holes closest together on the opposite end of the same side

- 9-7/8" between the holes furthest apart on the opposite end of the same side

- 10" between the holes directly across on the opposite side

I have included a diagram showing these measurements to help understand the spacing.

expert reply by: Scott S

0

Sliding Under Platform Pontoon Boat Ladder Mounting Hole Dimensions
(click to enlarge)

Answer 1

Your trailer looks awesome! The Road armor equalizers #LC696740 and Equa-Flex Cushioned Equalizers #LC279687 are both pretty similar in performance even though the Road Armor has two dampers. The main difference is the size of the equalizers. The…

view full answer...

Answer 2

The overall size of the Furrion Over the Range RV Convection Microwave part#FMCM15SS is 29-15/16" wide x 16-3/8" tall x 15" deep and requires a 30" cutout. If this matches the opening and size of the model you have this will be a…

view full answer...

Answer 3

I looked up the dimensions of your High Pointe EC942K9E and it's 15 inches deep, 15.7 inches tall, and 29.9 inches wide so the Furrion Over the Range RV Convection Microwave #FMCM15SS would easily fit in place of it and would also work really…

view full answer...

Answer 4

I believe you are referring to the XTRM Universal Sealant #34427034145-1. If so, it can absolutely be used in place of the original XTRM 100 that was on your roof. This will work just as well as the original sealant and its weather-resistant formula…

view full answer...

Answer 5

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 6

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 7

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 8

The best way to determine the height needed is to measure from the top of your trailer frame to the top of the sides of your boat. If the 40" Tall Guide-Ons #CE27626 sit right at or slightly above the sides of your boat then the shorter will…

view full answer...

Answer 9

That spindle looks pretty well destroyed so best option is going to be to replace the axle. You are going to need to measure your current axles in a few places to get the correct one as we don't have access to what your numbers reference. You…

view full answer...

Answer 10

Hey Chad, so I'd actually recommend a mid size ladder rack like the Yakima OutPost HD Overland Truck Bed Rack #Y01152-58. This is by far going to be your best bet if you don't want to trailer your kayaks. These bars have a 500 lb weight…

view full answer...

Answer 11

The Bargman 7-Way, RV-Style Connector #WG54006-043 referenced in your question uses the standard RV-style pin locations for its 7-Way connector. I have attached a diagram of these locations and their functions for you to check out. Wire colors will…

view full answer...

Answer 12

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Mounting Hole Spacing on the Sliding Under Platform Pontoon Boat Ladder

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching