Transmission Cooler for a 2010 Chevy Tahoe LTZ

Question

Question:

Hello I am curious to know if this part# D13503 will be compatible with my vehicle. I own a 2010 Chevy Tahoe LTZ 2WD with the transcooler mounted at the front of the radiator behind the front grille. If you have any install videos that would be greatly appreciated also, thank you very much.

asked by: Moises A

0

Expert Reply:

Transmission coolers like the Derale Series 8000 Plate-Fin Transmission Cooler Kit w/Barb Inlets - Class III item # D13503 are pretty universal. For your 2010 Chevy Tahoe you would want to use the Derale Series 8000 Plate-Fin Transmission Cooler Kit w/Barb Inlets - Class IV item # D13504. This is a larger Transmission cooler and would be a great replacement for your factory transcooler.

We do not have any installation videos for a 2010 Tahoe but we did install one on a 2009 GMC Yukon. I have linked the video below. You will also need the Derale Universal Bendable Metal Mount Kit item # D13002 and one Derale Snap-In Radiator Adapter Fitting for GM item # D13035.

expert reply by: Jerred H

0

Answer 1

You can bypass your factory cooler if you wanted to, but typically people use our coolers like the popular #D13503 as a supplemental cooler installed downstream of the factory cooler. To bypass yours though would only require you to run the lines of…

view full answer...

Answer 2

The Derale Combination Transmission and Engine Oil Cooler for GM Applications part #D15903 does not have a class rating. The class ratings are a guide that we use to help consumers pick the correct transmission cooler for their towing setup. They are…

view full answer...

Answer 3

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 8

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 9

There is a suggested and common method for 6 function trailer wiring. You will have the following functions: Right Turn, Left Turn, Ground, Tail/marker, Brake, Battery. I have included a help article on trailer wiring that includes a diagram and…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 12

From our experiences the Harbor Freight trailers like yours have a hub bore that requires a cap or Bearing Buddy that measures 2.047 inches like the #BB2047 you referenced. We don't have a standard cap that fits this size so the Bearing Buddy is…

view full answer...

Transmission Cooler for a 2010 Chevy Tahoe LTZ

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching