Can a Transom Tie Down Be Mounted To The Bunk Boards On A Boat Trailer?
Question:
I saw a Shorelander trailer with a bracket like this attached to the bottom side of a bunk as the transom tie down. I have a 14foot jon boat with a 50hp 2 stroke. Wil a bracket like this attached to a bunk provide sufficient support? What is the max recommend distance from the bunk support on the frame to the end of the bunk where this bracket would attach?
asked by: Aaron
Expert Reply:
The CE Smith Tie-Down Bracket # CE26214G really should not be attached to the end of the bunk board. The end of the board will rot over time as it is constantly being submerged in water for loading and unloading the boat. The bracket should be attached to the crossmember or the trailer frame.
You will then be able to secure your boat to the trailer using the Transom Tie-Down Straps # IMF14207.
Products Referenced in This Question
BoatBuckle Heavy Duty Ratchet Transom Tie-Down Straps - 2" x 4' - 833 lbs - Qty 2
- Boat Tie Downs
- S-Hooks
- 2 Straps
- Manual
- 0 - 5 Feet Long
- Ratchet Strap
- Transom Strap
- 1-1/8 - 2 Inch Wide
- 1501 - 2000 lbs
- BoatBuckle
more information >
Product Page this Question was Asked From
CE Smith Tie-Down Bracket for Boat Trailers - Galvanized Steel - Bolt On - Qty 1
- Boat Trailer Parts
- Tie-Down Anchors
- Tie-Down Anchor Brackets
- 1-15/16 Inch Wide
- 4 Inch Long
- CE Smith
more information >
Continue Researching
- Search Results: axle hub kit
- Search Results: tire minder
- Search Results: hub kit
- Search Results: tire minder i10
- Search Results: trailer idler hub assembly
- Search Results: l44649 kit
- Shop: BoatBuckle Pro Series Kwik-Lok Bow Tie-Down Strap w Loop End - 1" x 3' - 400 lbs - Qty 1
- Search Results: anti~rattle
- Shop: Trailer Idler Hub Assembly for 2,000-lb Axles - 5 on 4-1/2 - Galvanized
- Shop: Bearing Kit, L44649 Inner/Outer Bearings, 10-9 Seal
- Shop: TireMinder Smart TPMS for RVs - Signal Booster - 4 Tire Sensors
- Shop: Bearing Kit for 1" BT8 Spindle, L44643 Inner/Outer Bearings, 34823 Seal
- Shop: Easy Grease Trailer Idler Hub Assembly for 3.5K Axles - 5 on 4-1/2 - Galvanized
- Shop: Easy Grease Trailer Idler Hub Assembly for 2K Axles - 5 on 4-1/2 - Galvanized
- Shop: Trailer Wiring
- Video: LubriMatic Electrical Connector Dielectric Grease Review
- Video: Curt Trailer Plug Covers - 4 Flat Cover - C58750 Review
- Video: Curt Trailer Plug Covers - 4 Flat Cover - C58200 Review
- Video: BoatBuckle Kwik-Lok Bow Tie-Down Strap Review
- Video: BoatBuckle Kwik-Lok Transom Tie-Down Straps Review
- Video: Fulton Single Speed Trailer Winch Review and Installation
- Video: BoatBuckle Tie Down Straps - Trailer - IMF13111 Review
- Shop: Suspension Enhancement
- Q&A: Replacement Oil Cap for Dexter Hub # 21-35
- Q&A: How Long Is the Warranty On An Electric Over Hydraulic Actuator for Disc Brakes
- Q&A: Is There a Bolt On Bracket For Safety Chains on a Trailer
- Q&A: Which TorkLift SuperHitch Magnum w/ 2" & 2-1/2" Receiver For 2018 Chevy Silverado 2500 Short Bed
- Q&A: What Are Differences Between Bias (D) And Radial (R) Tires
- Q&A: Can I Replace Leaf Springs With Lower Rating For Better Ride Quality
- Article: Trailer Tire Sizing