Replacement Upper And Lower Cover For The Lippert Electric Trailer Jack 1817941

Question

Question:

Hi, I need the lower cover for a Lippert 1817941 Tongue Jack. Do you have those or a replacement cover? Thank you,

asked by: Ray H

1

Helpful Expert Reply:

For your Lippert Electric Trailer Jack 1817941, the correct bottom jack cover is the Replacement Bottom Jack Cover with Light Lens for Lippert Electric A-Frame Trailer Jacks # LC23UD.

If you ever should need the top cover as well, you can use the Replacement Top Cover for Lippert Electric Trailer Jack # LC285160.

expert reply by: Bryce D

1

Answer 1

The screws use a Phillips head, and to reach the recessed screws on the underside, you'll need a #2 Phillips screwdriver with a with a shaft length of at least 6 inches.

view full answer...

Answer 2

I have a solution for you but they do not offer just the lens for individual sale. You will need to use the Replacement Bottom Jack Cover with Light Lens for Lippert Electric A-Frame Trailer Jacks item #LC23UD. This will replace the lens and the…

view full answer...

Answer 3

I have included the video and a link to the original answer page that also has the video you are looking for. There are 4 screws on the bottom of the bottom cover holding it to the top. And if you remove the cap on the very top of jack #LC285318…

view full answer...

Answer 4

For a Lippert jack model 181794 a replacement manual crank nut is not available. I checked with my contact at Lippert to confirm. You will need to replace your jack with a complete new one, I am sorry to say. To help you select a new one I have…

view full answer...

Answer 5

Yes, I confirmed with Lippert that the Replacement Top Cover for Lippert Components Electric Trailer Jack part #LC285160 will fit your Lippert 3,500 Lb Electric tongue Jack 1817941.

view full answer...

Answer 6

I am not sure what your exact question is but the Lippert Power Gear Jack 181794 has been discontinued and there are no replacement parts available for this. Therefore, if you have an issue with yours then you will need to replace the entire jack and…

view full answer...

Answer 7

Lippert does not offer a replacement inner jack tube for their jack 1817941. When a jack is damaged in this way (which is more common than you want to know) it really is best to replace the entire jack for safety reasons. The outer tube on your jack…

view full answer...

Answer 8

The Bottom Jack Cover #LC23UD has four screws in it that hold the top to it. You'll need to remove those screws first and take the top #LC285160 off. Once the top is off you can then dismantle the bottom cover from the jack and slide it off. Once…

view full answer...

Answer 9

Optronics trailer tail light #ST45RB is potentially a fit for your trailer if the existing lights are one of the following: Uni Bond #SE4000R Wesbar #423541 Truck Lite #40282R/40202R Grote #52922 Peterson #426R Bargman #40-01-001 This information is…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 12

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Replacement Upper And Lower Cover For The Lippert Electric Trailer Jack 1817941

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching