Self Adjusting Brake Assemblies to Replace B12E-22

Question

Question:

we are working on a 2 axle trailer and i believe that it is a 7k axle looking for brake kits/drums, the label on the brake backing plate is a B12E-22 / AXLE TEK 12GG i think it is a 12x2 brake with 5 bolt mounting want to change it to the self adjusting brakes both sides L and R ALSO looking for the complete brake drums which are 8 lug. Do you have these in complete kits?

asked by: James J

1

Helpful Expert Reply:

The brake assemblies you have now are the # AKEBRK-6 so for a self-adjusting setup you'd want the part # 23-458-459. Then for a 7k hub with an 8 lug bolt pattern you'd want the part # AKHD-865-7-2-EZ-K.

expert reply by: Jameson C

1

Answer 1

Hey Jeff, yes the etrailer brake assemblies part #AKEBRK-6 is exactly what you have now so it would work great as a replacement for your assemblies that are marked B-12E-22 and BK-12-GG.

view full answer...

Answer 2

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 3

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 4

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 5

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 6

The recommended lug nut torque for your 7,000lb axle depends on a few factors like wheel size, stud size etc. Check out the attached photo which shows the torque specs for a variety of applications. I see you were looking at the Dexter Nev-R-Adjust…

view full answer...

Answer 7

I checked with Curt and they do show the Curt Trailer Hitch Receiver part #C13233 as a fit for a 2022 Volvo XC90 All Models which includes the Recharge.

view full answer...

Answer 8

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 9

The Dexter 072-078-00 is a 2,200 lb capacity leaf spring. You can use a higher capacity leaf spring, however it won't increase the capacity of your trailer as the axle is still rated for that max capacity of 4,400 lbs. My recommendation for a…

view full answer...

Answer 10

I checked your order notes and the leaf springs you bought last year were the part #e28SR which are for 5k axles. Since this is over the capacity of your axle failure would not have been caused by over loading the trailer assuming you stayed under…

view full answer...

Answer 11

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 12

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Self Adjusting Brake Assemblies to Replace B12E-22

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching