Replacement Manual Override Cap for a Ram 3,500 lb. A-Frame Jack

Question

Question:

Need to know if your Part# EJ-3520-BCP Replacement Manual Override Cap for the Etrailer A-Frame Electric Jack will fit a RAM 3500lb Electric A-Frame Jack. Thank you!

asked by: David S

0

Expert Reply:

Yes, it will fit. The Replacement Manual Override Cap for etrailer A-Frame Electric Jack # EJ-3520-BCP fits both an etrailer and Ram A-Frame trailer jack.

expert reply by: Scott S

0

Answer 1

I believe you're looking for the Replacement Manual Override Cap for etrailer A-Frame Electric Jack #EJ-3520-BCP. This will replace the manual override cap on your RAM 3.5K trailer jack, and is black in color.

view full answer...

Answer 2

The correct manual override cover for your 3,500lb electric Ram jack is the Replacement Manual Override Cap for etrailer A-Frame Electric Jack #EJ-3520-BCP. For a cover you can use the Ultra-Fab Protective Cover for Electric A-Frame Jacks…

view full answer...

Answer 3

Although I'm not sure what jack you have, we do have a handful of replacement caps for Ram jacks. Ram Square, Direct Weld, Sidewind Jack 10K - #TJD-12000-CP Ram Sidewind 2,000 lbs A-Frame Jacks - #TJA-2000S-CP Ram Swivel Marine MJ-1500B Series…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 6

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 7

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 8

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 9

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 10

A cover being installed on your spare tire would not prevent the Swagman Bike Rack part #S80501 from installing. The rack would still fit and work well. You might still compare the dimensions in the picture I attached with you spare tire so that you…

view full answer...

Answer 11

The installation instructions for this product are recommended for individuals who have experience winding torsion springs. If you have not worked with a torsion spring system before, we recommend contacting a local garage door company to install…

view full answer...

Answer 12

We have one option that will work for you. The Trailer Hub and Drum Assembly - 4,400-lb E-Z Lube Axles - 10" Diameter - 6 on 5-1/2 #8-407-5UC3-EZ uses inner bearing #L68149 and outer bearing #LM67048 so it would work perfectly on your spindle.…

view full answer...

Replacement Manual Override Cap for a Ram 3,500 lb. A-Frame Jack

Product Page this Question was Asked From

Continue Researching