Solution for Needing Replacement Power Cable of Furrion Shark Fin Bracket

Question

Question:

I am in need of the cord only that is included in the item you have “Replacement Shark Fin Camera Mounting Bracket for Furrion Vision S RV Camera Systems - Black - Qty 1 Item # FRCBRKT-BL” Do you sell just that cord?

asked by: Billie J

0

Expert Reply:

The only way we can get the cord that's in the Furrion bracket # FRCBRKT-BL is with the entire bracket.

expert reply by: Jameson C

0

Answer 1

The hitch ball angle adjustment on weight distribution systems is designed to provide more or less distribution of the tongue weight on your trailer hitch to the trailer and vehicle axles. If you adjust the ball angle farther away from the towing…

view full answer...

Answer 2

If you're prewired for Furrion then there will be a connector already there for the Furrion Vision S Wireless RV Observation Camera System w/ Side Marker Light Cameras - 5" Screen #FCE48TASL-05 to plug into. If you don't have a shark fin…

view full answer...

Answer 3

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Below is the general process for bleeding an electric over hydraulic brake actuator like #K71-650. Fill reservoir with NEW brake fluid. Never re-use brake fluid that has been salvaged or removed from another system. Remove the key from the breakaway…

view full answer...

Answer 6

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 7

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 8

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 9

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 10

The correct replacement leaf spring bushings for any given trailer will be dependent on the width and type of the leaf springs. The most common for a Dexter 10,000 lb Trailer Axle are 3" wide slipper springs. If you have 3" wide slipper…

view full answer...

Answer 11

To replace your WFCO WF-8750P power center I recommend the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K. This 2-in-1 AC/DC distribution panel and converter charger keeps your power systems easily…

view full answer...

Answer 12

I spoke with my contact at Progressive Dynamics and they informed me that the Lithium Converter for WFCO RV Power Centers part #PD4655LIV does work as an upgrade for the Parallax 7355. It has the same housing as the Replacement Converter for…

view full answer...

Solution for Needing Replacement Power Cable of Furrion Shark Fin Bracket

Product Page this Question was Asked From

Continue Researching