How Does Reverse Light Circuit Run to Buyers LED Trailer Tail Light BP53FR

Question

Question:

Buyers LED Trailer Tail Light - Stop, Tail, Turn, Backup - Submersible - Red and Clear Lens Item # BP53FR With both the 2 wire pigtail and the 3 wire pigtail needed for the back up lights......which wires get connected with the blue back up wire? Thank you,

asked by: Jeff H

0

Expert Reply:

The Buyers LED Trailer Tail Light - Stop, Tail, Turn, Backup - Submersible - Red and Clear Lens Item # BP53FR has two connectors for wiring harnesses on the back of it. The two prong port for the reverse light circuit which you'd use the # 421-49 for and the 3 prong connection part # A47PB which the other taillight circuits run to.

For the # 421-49 the reverse light circuit gets ran to the red wire and the white is grounded.

expert reply by: Jameson C

0

Answer 1

Yes, the 60" Horse Trailer Side Pad #HTP1260BK is essentially a universal option so you can install it wherever you're wanting to as long as you have the space for it. You'll need to pick up #8 x 3/4" sized screws for this…

view full answer...

Answer 2

I only have one recommendation as we do not carry a factory connector for the tail light harness on your 2008 Ford F-150. If your truck has a 7-way you will be able to use the Hopkins Endurance 5th Wheel/Gooseneck 90-Degree Wiring Harness #41157 to…

view full answer...

Answer 3

The easiest way to cut the oval hole for the Rubber Grommet, #a70gb, in my opinion, would be to use a Light Mounting Bracket for 6-1/2 inch Oval Trailer Lights, BK70BB, as a template and then use a hole saw the correct size to cut a hole on each end…

view full answer...

Answer 4

There are two color code standards that are used in the trailer world. The Hopkins 7-Way RV style connector and cable, #H20046, that you referenced uses the RV Industry standard color code which is as follows: White Wire - Ground Red Wire - Left…

view full answer...

Answer 5

Good morning, Crystal. We can certainly provide you with three of the TCL65 Trimax Trailer Wheel Chock and Lock #TMX75FR. That said, we do not offer a "keyed alike" option for these locks, nor can we guarantee a specific key number. So, we…

view full answer...

Answer 6

I have attached for you below some common torque values needed for a trailer suspension system but a lot of these will vary by bolt size and other factors. U-Bolts: Varies by Size - 1/2" bolts: 45 ft/lbs - 70 ft/lbs, 9/16" bolts: 65 ft/lbs…

view full answer...

Answer 7

The magnet should only make contact with the inside of the brake drum when power is applied to the magnet. If it is making contact with the drum all the time, you may have residual power running on the brake wire that is just enough to cause the…

view full answer...

Answer 8

Using the cut off wiring harness you have for the P3 part #90195 you will wire it to the brake controller wiring of your 2023 Ford Ranger which is sticking out of the large wire harness that goes through the driver's side firewall, left of the…

view full answer...

Answer 9

Sounds like you are wiring in a breakaway system to your trailer like the part #20099. I attached a diagram that shows how it all connects to a trailer's wiring. Basically the switch installs between the breakaway battery and the brake output…

view full answer...

Answer 10

The 4" Wide Continuous Hinge - 6' Long - 3/8" Pin Diameter #MA85VR is made from mill finished steel with a commercial die cut quality, however they are not coated with any rust preventative. With that being said, it would absolutely be…

view full answer...

Answer 11

Yes, because it is a 3-wire light, you can wire the Red Identification Light Bar with White LED Utility Light #OPT88FR to function as rear marker and reverse lights.

view full answer...

How Does Reverse Light Circuit Run to Buyers LED Trailer Tail Light BP53FR

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching