Do The Different Hitch Ball Sizes Have Different Heights As Well?
Question:
are the dimensions of a hitch ball from the bottom of the flange to the top of the ball standard. it looks like it might be 2 3/4inch for a standard 2inch ball. is it the same for a 2 5/16inch ball?
asked by: Andrew S
Expert Reply:
From the bottom of the flange to the very top of the ball will indeed be 2-3/4". This can vary slightly between manufacturers and ball size though, but the typical 1-7/8" ball ( # 19256) will measure +/- 2-5/8" tall, the typical 2" ball ( # 63845) will measure +/- 2-3/4" tall, and the typical 2-5/16" ball ( # C40030) will measure +/- 3-1/8" tall.
With that said, you should not be relying on the height of the ball to figure out how much rise or drop you need. This should be done by measuring from the inside top of the receiver hitch on your vehicle and from the ground to the bottom of the coupler on the trailer when on level ground. The coupler for the specific ball size takes this into account and is why you measure to the bottom of it and not the top. The ball mount platform that the flange on the bottom of the ball will sit on will match the bottom of the coupler (basically).
I know I went off on a bit of a tangent there, but I hope that helps.
Products Referenced in This Question
1-7/8" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 2000 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
2-5/16" Hitch Ball - 1-1/4" Diameter x 2-5/8" Long Shank - Chrome - 15,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2-5/16 Inch Diameter Ball
- 2-5/8 Inch Shank Length
- 1-1/4 Inch Diameter Shank
- 15000 lbs GTW
- Class IV
- Class V
- CURT
more information >
Product Page this Question was Asked From
2" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 7,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 7500 lbs GTW
- Class III
- Tow Ready
more information >
Continue Researching
- Article: Trailer Wiring Diagrams
- Article: How to Measure for Trailer Hitch Drop
- Article: How to Accurately Measure Trailer Leaf Springs
- Q&A: Replacement Brake Assemblies and Hub/Drums for 15k Dexter Axle
- Article: Ball Mount Basics: Weight Capacity, Class, and Size
- Article: Trailer Tire Sizing
- Q&A: No Turn or Brake Signals on Trailer on a Jeep Liberty with Tow Ready Harness 118524
- Article: Replacing RV Awning Fabric: Your Step-by-Step DIY Guide
- Q&A: Replacement for AL-KO 1530116 and 1530117 Brakes
- Q&A: Replacement Brake Shoes for 10 x 1-3/4-inch Brakes on 22-Foot Travel Trailer with 3500-lb Axles
- Q&A: Looking for Replacement Trailer Lamp Lens # 1A-S-20
- Article: Replacement Automotive Lighting
- Q&A: What are the Dimensions of a #99 Spindle
- Q&A: How To Charge 12v Batteries Wired in Parallel