Recommended Trailer Hitch Receiver and Wiring for Towing With 2013 Volkswagen Jetta SportWagen TDI

Question

Question:

I was wondering if you could help me figure out what equipment that I would need to install on a 2013 Volkswagen Jetta Sportwagen TDI 6spd. I will need the ability to tow a 5x8 Cargo mate, Blazer trailer, with trailer brakes equipped. Any guidance would be greatly appreciated.

asked by: Larry D

1

Helpful Expert Reply:

The first thing I recommend is checking your owner's manual. Make sure your 2013 VW Jetta SportWagen is capable of towing this trailer. Assuming it is, you will want a hitch, wiring, brake controller, and ball mount for a complete towing setup.

For a hitch, I recommend the EcoHitch Hidden Trailer Hitch Receiver # 306-X7284. This hitch has a concealed cross tube and a 2" receiver. It also has a maximum gross trailer weight of 2,000 lbs. You will be limited by whichever towing capacity is lower, the hitch or your vehicle.

For 4-way wiring you want the Curt # C59236. Once you have installed the 4-way you will need to install the Universal Installation Kit # ETBC7. This comes with the adapter, wiring, and everything else you will need to install a 7-way.

For a brake controller, check out the Redarc Tow-Pro Liberty Brake Controller # RED24FR. You will also need the # RED69FR wiring harness for installation. This brake controller mounts in an out of the way location leaving only the control knob visible in your vehicle. The control knob allows you to adjust the braking power and also acts as a manual override.

For a ball mount, I like the etrailer Ball Mount Kit # 989900. This kit has two ball mounts, one with a 3/4" rise or 2" drop and the other with a 2-3/4" rise or 4" drop. It also comes with a 1-7/8" and 2" ball, as well as a ball mount bag to store everything in.

I have attached some installation videos for your reference.

expert reply by: Robin H

1

Answer 1

So long as your trailer hub is able to accept larger wheels, you have the same bolt pattern, and there will be enough clearance for a larger tire you can change from a 12 inch wheel to a 15 inch wheel like the Dexstar Steel Spoke Trailer Wheel…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 7

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 12

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Recommended Trailer Hitch Receiver and Wiring for Towing With 2013 Volkswagen Jetta SportWagen TDI

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching