What Replacement Anti-Rattle Hitch Pin do I Need for My Yakima OnRamp # Y96FR?

Question

Question:

What anti-rattle hitch lock works with this Yakima bike rack?

asked by: Wayne V

0

Expert Reply:

The Yakima OnRamp # Y96FR already comes with an anti-rattle hitch pin. However, if you need a direct replacement, I confirmed with my tech at Yakima that the direct replacement is the Replacement Mounting Hardware - Anti-Rattle Bolt # Y8890176.

expert reply by: Bob C

0

Answer 1

The Yakima OnRamp Bike Rack for 2 Electric Bikes #Y88DJ you were looking at would actually be perfect. It looks like the Lectric 3.0 tops out at 64 lbs so the rack can handle the weight. It also uses padded clamps to hold it by the frame or seat…

view full answer...

Answer 2

Yes, the Yakima bike rack with a ramp you mentioned, the OnRamp, will indeed work with your ebike with a step-thru frame. The rack uses wheel straps and adjustable clamps to grasp bikes by their seat post or along the frame, which is why it is 100…

view full answer...

Answer 3

For your application I recommend using the Yakima OnRamp Bike Rack for 2 Electric Bikes because it uses ratcheting straps that go around your bikes, it has a weight capacity of 66 lbs per bike, and it comes with a ramp for easy loading and unloading.…

view full answer...

Answer 4

The Yakima OnRamp Bike Rack for 2 Electric Bikes does come in a 1-1/4" version which you can find here: #Y96FR. Since this carrier attaches to the bike's frame, it is compatible with bikes that have fenders, baskets, or oddly-shaped frames…

view full answer...

Answer 5

I have a great solution for you. The ramp on the Yakima OnRamp - 1-1/4" #Y96FR measures about 2 inches. However, I confirmed with Yakima that your bike with 2-1/2 inch tires will work just fine. They will just ride the side of the lips of the…

view full answer...

Answer 6

Good question, and there are just two differences between the Saris SuperClamp HD and EX, which is the size of the receiver(s) they fit and motorhome compatibility: - Compatible With Motorhome & Fits 2" Receiver Only: Saris SuperClamp HD…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 12

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

What Replacement Anti-Rattle Hitch Pin do I Need for My Yakima OnRamp # Y96FR?

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching