MORryde Cushioned Pin Box that Fits Montana High Country 310RE

Question

Question:

I am trying to determine what is the correct pin box is for my trailer. I have a 2017 Montana High Country 310RE is this something you can hep with or can you direct me where I can find the information ? Thank you.

asked by: LUIS J

0

Expert Reply:

From previous customers we know that your Montana High Country 310RE has a Lippert 1116 pin box so for a MORryde cushioned pin box like what you referenced you'd need the part # MR27VR.

expert reply by: Jameson C

0

Answer 1

The manufacturer and model number of the pin box is usually printed on a sticker or stamped into a plate or directly into the metal of the pin box. If you can't find that, the manufacturer of your 5th wheel should be able to tell you which pin…

view full answer...

Answer 2

I went ahead and reached out to my tech at Lippert (who designed the Rota-Flex #LC176440 for Curt), and they confirmed that the reason why Curt E series and Curt Q series hitches like the Curt Q16 is not compatible with the Rota-Flex is because the…

view full answer...

Answer 3

The psi should be listed on the sidewall of the tire. It is recommended that tires always be inflated to the max psi. Different tire manufacturers may have different psi ratings even for the same tire size and load range, so it's always best to…

view full answer...

Answer 4

I spoke with my contact at Lippert and this is what they sent me about the external sensor issue you have: External sensor error means there is an issue with the rear leveling sensor. This will be located 2-3 foot behind the rearmost axle. There may…

view full answer...

Answer 5

The "external sensor" error you're getting on the display of your Lippert leveling system like the Ground Control #LC358590 indicates an issue with the rear leveling sensor. This particular sensor should be located a few feet behind the…

view full answer...

Answer 6

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 7

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 8

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 9

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 10

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 11

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 12

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

MORryde Cushioned Pin Box that Fits Montana High Country 310RE

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching