Firestone Air Line Service Kit for Ride Rite Air Bag Kit

Question

Question:

I am taking a Firestone bag kit part F2613 and installing it in my new truck. Do you offer a new air hose and fitting kit? The new truck has a long bed.

asked by: Russell L

0

Expert Reply:

We have the Firestone Air Line Service Kit part # F2012 which comes with 18 foot of new air line, a couple elbow fittings, a union tee in case you want both bags inflated to same pressure, and a couple inflation valves.

expert reply by: Jameson C

0

Answer 1

Thanks for reaching out! Your installation of the Firestone Ride-Rite Air Helper Springs #F2613 on your 2022 Chevy Silverado 2500HD actually looks great! I reached out to my contact at Firestone just to confirm and they said adding some air pressure…

view full answer...

Answer 2

For your 2016 GMC Sierra 2500 the Firestone air bag kit part #F2613 is a confirmed fit. We had one customer with a similar concern come back and let us know how they dealt with the brake line. "On the left side there was a factory brake hose…

view full answer...

Answer 3

Yes, all of the Firestone Ride Rite air suspension systems use 1/4 inch tubing and 1/4 inch NPT fittings like the #F2012 that you referenced. This kit includes 18' of red 1/4" air line, (2) 1/4" NPT (National Pipe Thread) elbow…

view full answer...

Answer 4

Firestone union T fitting #F3025-1 is the correct one for your air bag kit #F2445 but since your air lines were also potentially damaged you may want to consider Air Line Service Kit #F2012 which includes the T, air lines, elbow fittings and Schrader…

view full answer...

Answer 5

The valve core can sometimes get stuck inside the valve stem due to corrosion build-up or being inserted incorrectly. This would then mean you could not put air in or take air out of the system. The good news is that this is pretty easy to fix and…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 10

A drop axle certainly can make it tough to reach the star wheel adjuster on a drum brake. The adjuster spoon tool we offer #W80630 has a 90-degree bend that will often let you get access to the adjuster even on a drop axle. Essentially you will need…

view full answer...

Answer 11

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 12

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Firestone Air Line Service Kit for Ride Rite Air Bag Kit

Product Page this Question was Asked From

Continue Researching