Weight of Redline Pre-Drilled Round Rubber Trailer Bumper # D3-96

Question

Question:

How much does this item weigh?

asked by: Ward S

0

Expert Reply:

The Pre-Drilled Round Rubber Trailer Bumper # D3-96 weighs 21lbs. It is 96" long, 3" wide and will stand 3" tall.

expert reply by: Bud M

0

Pre-Drilled Round Rubber Trailer Bumper # D3-96 Dimensions
(click to enlarge)

Answer 1

What you'd want to do is drill holes in the Pre-Drilled Round Rubber Trailer Bumper #D3-96 to match the mounting holes of your trailer and you'd be set. The bumper is rubber so it would be easy to drill. The pre drilled holes of this…

view full answer...

Answer 2

The holes on your existing bumper seem to be about 11 inches apart. The holes on bumper #D3-96 are also 11 inches apart. You may have to drill a hole or two to get it lined up with the first hole but then it should line up nicely. I have also…

view full answer...

Answer 3

We have 3 different rubber bumpers that you can use for your horse trailer. They all measure 96" long but have different widths so you'll just need to choose the appropriate width: 2-1/16" Width - #D2-96 3" Width -…

view full answer...

Answer 4

All of our bumper strips are 96" long and have the holes pre-drilled out at 11" on center, but the nice thing is these can be cut and re-drilled to accommodate your application. You just need to choose which one has the width…

view full answer...

Answer 5

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex…

view full answer...

Answer 6

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 7

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 8

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 9

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 10

You would not be able to charge your battery through the wiring on your 4-way trailer connector. Since your truck has a 7-way connector, you could maintain the power to the battery but not charge it. To begin, you would need to cut off your 4-way…

view full answer...

Answer 11

I can end this debate for you real fast! Trailer tires, which will have an ST in front of the size, should always be inflated to the maximum psi indicated on the tire. Trailer tires usually do not have a recommended and maximum psi indication so I am…

view full answer...

Answer 12

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Weight of Redline Pre-Drilled Round Rubber Trailer Bumper # D3-96

Product Page this Question was Asked From

Continue Researching