Could Pre-Drilled Round Rubber Trailer Bumper # D3-96 Replace Bumper with Different Hole Spacings

Question

Question:

The bumper guard D3-96 would replace an existing bumper on a Kiefer horse trailer. The existing bumper is attached with bolts and they are spaced 19.5” on center. What is your advise?

asked by: Diane

0

Expert Reply:

What you'd want to do is drill holes in the Pre-Drilled Round Rubber Trailer Bumper # D3-96 to match the mounting holes of your trailer and you'd be set. The bumper is rubber so it would be easy to drill. The pre drilled holes of this are 11 inches apart so it wouldn't match perfectly.

expert reply by: Jameson C

0

Answer 1

We have 3 different rubber bumpers that you can use for your horse trailer. They all measure 96" long but have different widths so you'll just need to choose the appropriate width: 2-1/16" Width - #D2-96 3" Width - #D3-96 4"…

view full answer...

Answer 2

Since the Redline Pre-Drilled Round Bumpers, part #D3-96, part #D2-96, and part #D4-96, are made of rubber I see no reason why you cannot drill out mounting holes so that they are custom to your hole patterns. If you will be using the full 96 inches…

view full answer...

Answer 3

While there isn't a bumper that has 12 inch bolt hole spacing, you can still use the 96" long x 3" wide Pre-Drilled Round Rubber Trailer Bumper #D3-96. What you could do is drill the necessary holes at the spacing you need and it will…

view full answer...

Answer 4

All of our bumper strips are 96" long and have the holes pre-drilled out at 11" on center, but the nice thing is these can be cut and re-drilled to accommodate your application. You just need to choose which one has the width you're…

view full answer...

Answer 5

The holes on your existing bumper seem to be about 11 inches apart. The holes on bumper #D3-96 are also 11 inches apart. You may have to drill a hole or two to get it lined up with the first hole but then it should line up nicely. I have also…

view full answer...

Answer 6

The Pre-Drilled Round Rubber Trailer Bumper #D3-96 weighs 21lbs. It is 96" long, 3" wide and will stand 3" tall.

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 9

You can put a maintenance charge on your trailer battery with the 12 volt accessory circuit of the 7-way. The 1:00 position of your 7-way carries this circuit. You would just need to run a length of 10 gauge wire like part #10-1-1 (sold by the foot),…

view full answer...

Answer 10

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 11

You would not be able to charge your battery through the wiring on your 4-way trailer connector. Since your truck has a 7-way connector, you could maintain the power to the battery but not charge it. To begin, you would need to cut off your 4-way…

view full answer...

Answer 12

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Could Pre-Drilled Round Rubber Trailer Bumper # D3-96 Replace Bumper with Different Hole Spacings

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching