What Drill-On Roof Rack will Fit My 2022 Chevy Equinox?

Question

Question:

i didnt notice this new 2022 equinox doesn`t have ports or rails for a roof rack , i would rather have a rack that is installed on / in the metal of the top . Everything i looked @ on line shows to clamp it on side or door ? I`m sure someone could drill through roof and anchor some ports . please advise .thanks

asked by: Jimmy O

0

Expert Reply:

I have an answer for you. Unfortunately, if you are looking to drill into your roof to install a roof rack on your 2022 Chevrolet Equinox, we do not have anything that we have tested as far as a drill-on solution for your bare roof.

With that being said, the best solution is the Yakima 54" Tracks for Roof Racks # Y01127 along with 4 of the Yakima Control Tower - Qty. 1 # Y8890027 and two sets of the Landing Pad 1 # Y00221 (Qty. 2). With these components, you will be able to attach Yakima Round Bars like the Round 48" Crossbars # Y00408.

It is important to note that, based on the length of your roof, you may need to cut the 54" inch tracks down to size. Also, you may need to drill nuts at different locations designated in the owner's manual if you have a defined curvature of your roof.

However, with all this being said, the system we recommend is a clip-on roof rack system that involves the following parts:

- Thule WingBar Evo Crossbars - Aluminum - Black - 53" # TH711420
- Evo Clamp Feet for Thule Crossbars - Naked Roofs # TH710501
- Fit Kit for Thule Evo Clamp Roof Rack Feet - 5206 # TH145206
- Thule One-Key Lock Cores # TH450400

With this system, the Evo Clamp feet and Fit Kit 5206 are designed specifically for a secure fit on your 2022 Equinox. While this is not the exact system you are looking for, I recommend sticking with this setup since it is a confirmed fit for your vehicle.

expert reply by: Bob C

0

Answer 1

We have a variety of roof rack solutions for the bare roof on your 2024 Chevy Equinox, and for your application I recommend the Rhino-Rack ROC25: - Rhino-Rack ROC25 Roof Rack for Naked Roofs #RR53TR This uses clamps on your door jambs but it has the…

view full answer...

Answer 2

Aside from a slight change in the appearance of the crossbar (the WingBar Evo has some boxed edges as opposed to the completely smooth front of the AeroBlade) the biggest differences are the rubber strip on top of the crossbar and the weight…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 5

Tracks can absolutely be installed on the roof of your A.R.E. Truck Cap to provide a mounting system for a roof rack. For this I recommend the Yakima Tracks, which come in 42 inch #Y01126, 54 inch #Y01127, and 60 inch #Y01135 lengths. These tracks…

view full answer...

Answer 6

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Gary, so the Yakima 54" Tracks for Roof Racks #Y26RR that you referenced are compatible with your setup as they provide the standard dimension roof tracks that your Sherpa Crows Nest was designed to fit. With that said the correct T-bolt…

view full answer...

Answer 9

First of all, thanks for the picture of your cute doggy! Yes, you can use a Thule Hullavator Pro item #TH898 or Yakima ShowDown item #Y04081. I can't tell from your picture but there were versions of the A.R.E. camper shells that had tracks on…

view full answer...

Answer 10

Hey Alec, For your 2016 Ford Fusion I recommend the recommend a roof rack from Inno: Inno Aero Crossbars #INXB138-145 Inno Through Feet for Aero Crossbars #INXS250 Custom Fit Kit for Inno XS200, XS250, and INSU-K5 Roof Rack Feet #INK860 As with any…

view full answer...

Answer 11

Thanks for reaching out, Joe! I recommend using the Rhino-Rack Aero Bar Roof Rack for Camper Shells #Y02-480B which comes with 63" long tracks as well as 54" long crossbars which should give you a little bit of overhang on your canopy. Per…

view full answer...

Answer 12

Congrats on the new vehicle! To flat tow your 2024 Chevy Equinox you will need the following parts: Tow Bar and Safety Chains - Roadmaster Falcon 2 Tow Bar item #RM-520 and item #RM-643 Base Plate Kit - Roadmaster Direct-Connect Base Plate Kit -…

view full answer...

What Drill-On Roof Rack will Fit My 2022 Chevy Equinox?

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching