How To Install The Curt Auxiliary LED Indicator Lights C53201 With Load Resistors DI34ZR
Question:
Hello. I have a 4-bike, hitch-mounted Kuat bike rack. I have been pulled over twice now for the rack not having lights and the mounted bikes obstructing my vehicles taillights. I want to mount some lights and the subject Curt lights seem like the best alternative. However, I already know load resistors will be required for my vehicle. Your QandA section recommends DI34ZR for use with the Curt lights. However, I cant find any installation instructions. I like the Kurt lights because they use simple connectors. However, it appears the resistors would have to be spliced in somewhere. Before I purchase, do you have instructions or a diagram of how these resistors are installed with the Kurt lights? Thanks.
asked by: Theodore E
Expert Reply:
To wire the Load Resistor Kit for LED Turn Signals # DI34ZR into your vehicles turn signals you will need to find your turn signal wire for your vehicle. Once that wire is identified, take the one end of the wire and the turn signal wire and connect to the quick splice connector. Make this connection by crimping the wires together with a crimping tool like # PTW30764. From here you'll connect the other white wire and ground this wire to a good ground source.
The Curt Auxiliary LED Indicator Light # C53201 is even easier to install, simply plug the 4 way flat connector into your existing 4 way connector, and color match the plugs to the receptacles.
Products Referenced in This Question
Load Resistor Kit for LED Turn Signals - 50 Watts - 6 Ohm - Qty 2
- Accessories and Parts
- Trailer Lights
- Load-Resistor Kit
- Diamond
more information >
Performance Tool Crimping Pliers - 10 to 22 AWG Wire - 9-1/2" Long
- Electrical Tools
- Wiring Tools
- Wire Crimper
- Red
- Performance Tool
more information >
Product Page this Question was Asked From
Curt Auxiliary LED Indicator Lights
- Accessories and Parts
- Hitch Bike Racks
- Hitch Cargo Carrier
- Lights
- CURT
more information >
Continue Researching
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Shop: T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Curt Auxiliary LED Indicator Lights
- Article: Hitch Adapters and Extenders
- Video: Tekonsha T-One Vehicle Wiring Harness Installation - 2019 Chevrolet Spark
- Video: Curt Auxiliary LED Indicator Lights Review C53201
- Shop: Draw-Tite Sportframe Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Video: Review of Curt Hitch Cargo Carrier - Hitch Bike Rack - C53201
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Video: Curt Class I Trailer Hitch Installation - 2017 Chevrolet Spark
- Q&A: Does Tekonsha Wiring Harness Fit 2022 Chevy Spark ACTIV
- Q&A: Recommended Trailer Hitch Receiver and Bike Rack For Carrying 2 E-Bikes With a 2018 Chevrolet Spark
- Shop: Windshield Wiper Blades
- Shop: Vehicle Tow Bar Wiring
- Video: Curt Auxiliary LED Indicator Lights Review
- Shop: 19x47 Curt Cargo Carrier for 1-1/4" and 2" Hitches - Steel - 300 lbs
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Video: Curt Class I Trailer Hitch Installation - 2021 Chevrolet Spark
- Video: Review of etrailer Hitch Alignment - Hitch Pin Alignment Collar - e98942
- Article: Routing the Power Wire for a Trailer Wiring Harness
- Article: Brake Controller Installation: Starting from Scratch
- Article: My Trailer Hitch Doesn't Fit
- Q&A: How To Install Trailer Lights On A BV Hitch-Mounted Bike Rack
- Q&A: Lighting Solution for Kuat NV 2.0 Bike Rack
- Q&A: Recommended Auxiliary Light Kit For a Kuat Bike Rack
- Q&A: Kuat Base NV 2.0 Bike Rack Needs Tail Lights
- Q&A: What is the Difference Between the Kuat NV 2.0 and the Older Version of the Rack
- Search Results: 4 pin splitter
Walt
3/16/2024
53201. No indication which is left or right. Just Y and B. Running through tubes so has to be correct first time. Car not wired yet so no test possable