Diameter of 2,000 lb Trailer Axle with Idler Hubs e82GR

Question

Question:

What diameter pipe is this axle?

asked by: Manuel G

0

Expert Reply:

The diameter is 1-3/4 inches of the Trailer Axle with Idler Hubs # e82GR.

The # e82GR is a 2,000 lb axle with an idler hub on it that has a 5 on 4-1/2" bolt pattern. It measures 60" from hub face to hub face and 48" from spring center to spring center and you'll want to make sure your axle also has those same measurements if you are looking to replace it.

expert reply by: Kyle S

0

Answer 1

L-brackets like the part #CE26098G-2 are a great option for installing the CE Smith Fenders part #CE19503-2. If the fenders will mount right up to the side of the trailer frame I would go with the #PF1135-BKT-2 though as this would be easiest way…

view full answer...

Answer 2

Thank you for the photos! According to my information and what you sent in, your best option for a replacement fender is the CE Smith Black Fender: CE Smith Single Axle Trailer Fender w/ Top and Side Steps - #CE19503 (Qty 1) CE Smith Single Axle…

view full answer...

Answer 3

I was able to go out to the warehouse and measure the mounting brackets holes for the PF11X35W and found that it was 5-5/16 inches or 5.3125 inches. If these aren't an exact match, new holes can usually be drilled into the brackets to make…

view full answer...

Answer 4

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 5

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 6

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need…

view full answer...

Answer 7

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 8

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for…

view full answer...

Answer 9

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 10

Below is the general process for bleeding an electric over hydraulic brake actuator like #K71-650. Fill reservoir with NEW brake fluid. Never re-use brake fluid that has been salvaged or removed from another system. Remove the key from the…

view full answer...

Answer 11

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 12

The great thing about Bearing Buddy like part #BB1781 is that when you add grease to your system with the included fitting, it will move the spring-loaded piston outward and allow grease to seep around the edges to keep from damaging the seal. You…

view full answer...

Diameter of 2,000 lb Trailer Axle with Idler Hubs e82GR

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching