Knapheide Truck Bed Box Replacement Key

Question

Question:

Hello, I wanted to ensure that this key would fit my lock boxs. it is a Knapheide truck bed box. it is a 1998 truck bed box with a serial number 65849TK and the lock says it is CH509. thank you

asked by: Adam A

0

Expert Reply:

Yes, I can confirm that the Replacement Key for UWS Toolboxes - CH509 item # KEYCH509 will fit your Knapheide truck bed box.

expert reply by: Jerred H

0

Answer 1

The Replacement Key for UWS Toolboxes #KEYCH509 will not say CH509 on it; however, you can simply use a permanent marker to write a key number on it, or put something like athletic tape on the key and write it on the tape if you are concerned the…

view full answer...

Answer 2

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

Since the issue appears to be on the vehicle side for your 2017 Toyota Tacoma, I recommend first checking the connector itself. Look to see if there is any dirt or corrosion built up inside the connector that may preventing a solid connection with…

view full answer...

Answer 8

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 9

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 10

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 11

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 12

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Knapheide Truck Bed Box Replacement Key

Product Page this Question was Asked From

Continue Researching