Replacement Hub/Rotor for 2002 EZ Loader Boat Trailer With Surge Disc Brakes
Question:
I have 2002 ez loader boat trailer with surge disc brakes and I need to replace hubs
asked by: Steven R
Expert Reply:
In order to find out which disc brake kit fits your boat trailer, you are going to need some additional information. You will want to find the axle capacity, wheel diameter, wheel bolt pattern, and which bearings and seals fit the spindle on your axle.
You may be able to find the part numbers on the bearings and seal. If you are unable to locate them, or if they have worn off, you will have to take some measurements. I recommend using a digital caliper like the # PTW80157. See the diagram below which shows where to measure and where to find the part numbers.
The Kodiak Disc Brake Kit # K2HR35D is for a 3,500 lb axle. This fits 13" and larger wheels with a 5 on 4-1/2 bolt pattern, and has a 4 bolt brake flange configuration. It fits a #84 spindle with a # L68149 inner bearing, # L44649 outer bearing, and # RG06-050 grease seal. If you find that this kit matches what you have then it is the correct replacement.
I have attached a helpful article on adding disc brakes that you can check out, along with a link to all of our available disc brake kits.
Products Referenced in This Question
Replacement Trailer Hub Bearing - L44649
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- 1.063 Inch I.D.
- Bearing L44649
- Race L44610
- 3500 lbs Axle
- etrailer
more information >
Replacement Trailer Hub Bearing - L68149
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- 1.378 Inch I.D.
- Bearing L68149
- Race L68111
- 3500 lbs Axle
- etrailer
more information >
4" Carbon Fiber Digital Caliper
- Hand Tools
- Measuring and Layout Tools
- Digital Calipers
- Carbon Fiber
- Performance Tool
more information >
Grease Seal - Double Lip - ID 1.719" / OD 2.565" - for 3,500-lb Axles - Qty 2
- Trailer Bearings Races Seals Caps
- Seals
- Grease Seals - Double Lip
- 1.719 Inch I.D.
- 2.565 Inch O.D.
- etrailer
more information >
Product Page this Question was Asked From
Kodiak Disc Brake Kit - 10" Hub/Rotor - 5 on 4-1/2 - Dacromet - 3,500 lbs
- Accessories and Parts
- Trailer Brakes
- Disc Brakes
- LH
- RH
- 3500 lbs
- Brake Assembly
- 5 on 4-1/2
- Hub and Rotor Assembly
- Kodiak
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Article: Parts Needed to Add Hydraulic Disc Brakes to a Trailer
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: How to Bleed Electric Over Hydraulic Trailer Brakes
- Article: 4 Steps to Choosing Your 5th Wheel Pin Box
- Article: Breakaway Kit Installation for Single and Dual Brake Axle Trailers
- Q&A: Do Trailer Tires and Wheels Need to be Balanced
- Q&A: Magnetek Series 6300A Model 6332 Replacement Converter
- Q&A: Replacement Recommendation for TDE 46210 Hub
- Article: Most Popular Wheel Bearings
- Q&A: Recommended Cover for a Lance Truck Bed Camper Model 1010
- Q&A: Will the Demco Brake Actuator # DM8202022 Work with Disc Brakes on a Boat Trailer
- Q&A: Required Bolt Length for Installing A-Frame Trailer Jack
- Article: Where to Position the Trailer Axle?
- Article: Trailer Drum Brakes vs. Disc Brakes: Making the Decision