Does Curt Hitch Extension # C45048 Require Safety Chains Ran to Hitch

Question

Question:

I am using this extension at 24, I have seen people use turn buckles or straps going from the chain loops on the end where the ball goes in back to the reciever hitch or frame. Is this required?

asked by: Keith D

1

Helpful Expert Reply:

With the Curt hitch extension part # C45048 you do not need to run chains back to the hitch of the vehicle. What you have seen is most likely a Torklift extension like the # TLE1636 which is a totally different setup.

expert reply by: Jameson C

1

Answer 1

We definitely know about the issue you are referring to. We have just the part for you! Furrion recently came out with a brand new adapter for your 2022 GMC Sierra 1500 Limited to work with your camera system. The part you need is the 7-Way Vehicle…

view full answer...

Answer 2

Yes, this Curt Hitch Extension and Reducer #C45048 does have a slight bend in it and that is normal. It is hard to see this bend in our photos on the site but you can easily see in our product video that it does have the bend as it moves on the…

view full answer...

Answer 3

We have the Curt hitch extender that fits 2-1/2 inch hitches part #C45048 and can be trimmed down from 34 inches to 24 inches. At 34 inches it has a capacity of 6,000 lb trailer weight and at 24 inches 8,000 lbs trailer weight.

view full answer...

Answer 4

I am assuming by heavy duty sway control system that you have a weight distribution system, something like part #EQ37120ET. If that is the case then your best option to consider would be an extended shank. The longest shank we offer is the…

view full answer...

Answer 5

Any 12" extender that would fit your application will reduce your overall hitch weight capacity. The Brophy Hitch Extender #RHE12 (14") will reduce it by 33-1/3% while most others will reduce it by 50%. Options like the Curt Hitch…

view full answer...

Answer 6

A good option for a safety chain for use with Curt hitch extender part #C45048 is the Laclede Chain Safety Chains and Cables, part #2118-348-04. These offer a minimum breaking strength of 5000-lbs and are USA-made.

view full answer...

Answer 7

The closest adapter we have to what you need is the Curt hitch adapter part #C45048. This fits a 2-1/2 inch hitch and provides a 2 inch hitch opening but it's minimum length is 24 inches. The only other pre-drilled option is the part #HR26.

view full answer...

Answer 8

Best hitch extension option we have for your 2018 Ram 3500 with a 2-1/2 inch hitch that has a camper in the bed and is towing a pontoon boat is the Curt extension part #C45048. This extension can be used at either 24 or 34 inches in length and would…

view full answer...

Answer 9

If you use the Curt hitch extender part #C45048 in the 24 inch length with a weight distribution system the towing capacity is 8,000 lbs. If the 24 inch length would work for you this would be a great option.

view full answer...

Answer 10

Thank you very much for your question, I recommend the Curt Hitch Extension and Reducer for 2-1/2" Trailer Hitches - 24" to 34" Long #C45048. I would measure how far the Lance Camper hangs over the back of the truck so we can make a…

view full answer...

Answer 11

I have two options that will allow for you to extend the connection point between your truck and trailer. The best option for you will depending on the gross trailer weight (GTW) and tongue weight (TW) of your trailer. As long as the GTW and TW of…

view full answer...

Answer 12

We do have great hitch extender options for trucks like your that have 2-1/2 inch hitches like the Curt part #C45048 but the #TLE1642 only fits the new Ram trucks that have 3 inch hitches. The Curt #C45048 can be used as a 34 inch extension or cut…

view full answer...

Does Curt Hitch Extension # C45048 Require Safety Chains Ran to Hitch

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching