Hitch Extension Recommendation for 2-1/2 inch Hitch

Question

Question:

Need a ~~12inch long receiver reducer 2.5inch to 2. simply a 2.5inch square tube with 1/4inch walls. 2.5OD, 2.0ID. 10inch min length.

asked by: Chris H

0

Expert Reply:

The closest adapter we have to what you need is the Curt hitch adapter part # C45048. This fits a 2-1/2 inch hitch and provides a 2 inch hitch opening but it's minimum length is 24 inches. The only other pre-drilled option is the part # HR26.

expert reply by: Jameson C

0

Answer 1

We definitely know about the issue you are referring to. We have just the part for you! Furrion recently came out with a brand new adapter for your 2022 GMC Sierra 1500 Limited to work with your camera system. The part you need is the 7-Way Vehicle…

view full answer...

Answer 2

Any 12" extender that would fit your application will reduce your overall hitch weight capacity. The Brophy Hitch Extender #RHE12 (14") will reduce it by 33-1/3% while most others will reduce it by 50%. Options like the Curt Hitch Extension…

view full answer...

Answer 3

A good option for a safety chain for use with Curt hitch extender part #C45048 is the Laclede Chain Safety Chains and Cables, part #2118-348-04. These offer a minimum breaking strength of 5000-lbs and are USA-made.

view full answer...

Answer 4

I am assuming by heavy duty sway control system that you have a weight distribution system, something like part #EQ37120ET. If that is the case then your best option to consider would be an extended shank. The longest shank we offer is the…

view full answer...

Answer 5

Yes, this Curt Hitch Extension and Reducer #C45048 does have a slight bend in it and that is normal. It is hard to see this bend in our photos on the site but you can easily see in our product video that it does have the bend as it moves on the…

view full answer...

Answer 6

We have the Curt hitch extender that fits 2-1/2 inch hitches part #C45048 and can be trimmed down from 34 inches to 24 inches. At 34 inches it has a capacity of 6,000 lb trailer weight and at 24 inches 8,000 lbs trailer weight.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 9

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 12

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Hitch Extension Recommendation for 2-1/2 inch Hitch

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching