Trailer Hitch and Towing Accessories Recommended for 2021 Toyota RAV4
Question:
I'm undecided between the Curt C13416 and the etrailer Class 3 hitches for my 2021 Toyota RAV4. Which one is recommended?
asked by: Brad C
Expert Reply:
The Curt # C13416 and etrailer # e23ZR are very similar in appearance. The etrailer item # e23ZR has a higher tongue weight capacity at 675 lbs versus 600 lbs for the Curt, but due to the lower towing/tongue weight capacity of the vehicle which on vehicles with the tow package is 3500/385 lbs respectively, the tongue weight capacity differences between the two is moot, because you'll be limited by the capacity of the vehicle itself.
The two hitches are visually very similar and would install in the same manner, but if I had to choose between the two, I'd go with the Curt # C13416 because Curt does a slightly better job on their powder coat and because the hitch itself is manufactured in the USA (though the hardware could be from elsewhere).
If you'll be towing with the hitch, you'll also need a # C56434 trailer wiring harness, a # D-28 ball mount along with a # PC3 hitch pin and a # 19260 1-7/8 or a # 63845 2 inch hitch ball.
I've linked to some installation videos that you might find helpful.
Products Referenced in This Question
1-7/8" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 2000 lbs GTW
- Class III
- Draw-Tite
more information >
2" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Chrome - 7,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 1 Inch Diameter Shank
- 7500 lbs GTW
- Class III
- Tow Ready
more information >
Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- CURT
more information >
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 14-1/4" Long - 6,000 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 6 Inch
- Rise - 4 Inch
- Fits 2 Inch Hitch
- 6000 lbs GTW
- Class III
- Long Shank
- CURT
more information >
etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 600 lbs TW
- 4000 lbs GTW
- 4000 lbs WD GTW
- 2 Inch Hitch
- 600 lbs WD TW
- Concealed Cross Tube
- etrailer
more information >
Pin and Clip for 2" and 2-1/2" Hitches - 5/8" Diameter x 3-1/4" Span
- Hitch Pins and Clips
- Standard Hitch Pin
- Fits 2 Inch Hitch
- Fits 2-1/2 Inch Hitch
- 5/8 Inch Diameter
- 4 Inch Span
- Draw-Tite
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 600 lbs TW
- 4000 lbs GTW
- 2 Inch Hitch
- Concealed Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Picking Out Replacement Axle for Snowbear 550LHD Trailer
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: Troubleshooting A Clunking Noise Between A Fifth Wheel Hitch And Base Rails While Towing
- Q&A: Trailer Hitch for a 2015 Honda Pilot
- Q&A: Parts Needed to Tow a Trailer with a 2015 Honda Pilot
- Q&A: When Flat Towing a Vehicle How Much Tongue Weight is on the Trailer Hitch
- Q&A: Installation of Hitch on Fifth Wheel Trailer
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Q&A: Replacement Parts for Fan-Tastic Vent 8000 Series
- Article: Trailer Tire Sizing
- Article: Trailer Wiring Diagrams
- Article: My Trailer Hitch Doesn't Fit
- Article: Replacement Automotive Lighting