Trailer Wiring Harness for a 2012 Volkswagen Jetta SportWagen TDI

Question

Question:

will Part 119147KIT function in a 2012 Jetta sportwagen TDI, as well?

asked by: Robert

0

Expert Reply:

Yes, you can use trailer wiring harness # C59496 on a 2012 Volkswagen Jetta SportWagen TDI. I have included a link to the installation instructions for you to view.

expert reply by: Michael H

0

Answer 1

The T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector #118572 should be compatible with your 2011 VW Golf Wagon if you hardwire the connections but it has not been tested to confirm. The confirmed fit for your 2011 VW Golf Wagon is the…

view full answer...

Answer 2

The only trailer wiring harness currently available for your 2012 Volkswagen Jetta is #118572. I have included a link to a video to the right that shows how this harness installs. I have also linked the instructions.

view full answer...

Answer 3

The internal components of trailer wiring harness #118572 are designed to work with the sedan models of the 2013 Volkswagen Jetta so even cutting off the connectors and attempting to hardwire it in will not work properly and it will void the warranty…

view full answer...

Answer 4

To determine the correct wiring for your trailer you will need to use a circuit tester, item #PTW2993, and attach the wires from the connector by function only. The light wires should be as follows, red is the stop turn wire and the black is the…

view full answer...

Answer 5

Not every vehicle has a custom install wiring kit available unfortunately. Typically the vehicles that are more likely to tow will have plug and play install kits and the lighter duty vehicles that don't tow as often will need to use a hardwired…

view full answer...

Answer 6

I will be happy to help you get everything you will need to tow a trailer and go on the road with your band: except roadies. We are all out of roadies. First, you will need a trailer hitch. I recommend the EcoHitch Hidden Trailer Hitch Receiver -…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 10

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 11

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 12

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Trailer Wiring Harness for a 2012 Volkswagen Jetta SportWagen TDI

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching