Tire Pressure Recommendation For 1,300LB Burro Camping Trailer Kenda Loadstar 175/80D13

Question

Question:

What PSI would you recommend for a vintage 13 ft Burro Camping Trailer with this type of wheel/tire? Though we do need to get it weighed, it is probably around 1300 lbs.

asked by: Andrea S

0

Expert Reply:

Kenda recommends to run their tires at the maximum psi rating found on the sidewall regardless of trailer weight capacity.

The Loadstar ST175/80D13 Bias Trailer Tire with 13" Galvanized Wheel # AM3S130 should be ran at 50psi cold tire pressure.

expert reply by: Bud M

0

Answer 1

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 2

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5…

view full answer...

Answer 3

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 4

The Replacement Crank Extension for Lippert Components Spare Tire Winch Assemblies #LC1315411, which is a replacement for Lippert Components Spare Tire Winch with Offset Cable #LC159056, has an inside diameter of 0.50 inches and the hex has a 0.75…

view full answer...

Answer 5

There are going to be two parts to the handle that you will need to operate the Lippert Components Spare Tire Winch part #LC159056. The first of which is the intermediate shaft or what Lippert calls a Crank Extension part #LC1315411. This will be…

view full answer...

Answer 6

I was able to find the OEM part number for the Chevy spare tire hoist but I was unable to find a weight capacity rating on it. The owner's manual for the 2015 Chevy Silverado 1500 and the original hoist can handle the weight of a full sized spare…

view full answer...

Answer 7

The great thing about Bearing Buddy like part #BB1781 is that when you add grease to your system with the included fitting, it will move the spring-loaded piston outward and allow grease to seep around the edges to keep from damaging the seal. You…

view full answer...

Answer 8

The crank handle for the Lippert Components Spare Tire Winch with Offset Cable item #LC159056, is Replacement Crank Extension for Lippert Spare Tire Winch Assemblies - 35-1/2" item #LC1315411. The Spare Tire Winch item #LC159056 has a 1/2-inch…

view full answer...

Answer 9

The Lippert Components Spare Tire Winch with Offset Cable #LC159056 will not have any locking or hold mechanism short of being completely reeled in. I spoke to my tech contact at Lippert who has this on his truck and he said you just crank it up…

view full answer...

Answer 10

To raise and lower the Lippert Spare Tire Winch with Offset Cable #LC159056 what you need is the replacement manual crank handle part #LC119226.

view full answer...

Answer 11

The Lippert Components Spare Tire Winch with Offset Cable #LC159056 requires the handle #LC119226 to crank up and down.

view full answer...

Answer 12

It is possible to over-fill a hub that has a Bearing Buddy bearing protector such as #BB1781. The convenience of easy filling through the zerk fitting can often mean we can be tempted to keep adding more grease. ("If a little is good, then more…

view full answer...

Tire Pressure Recommendation For 1,300LB Burro Camping Trailer Kenda Loadstar 175/80D13

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching