Replacement 5 on 4 3/4 Hub With LM67048 Inner Bearing and LM11949 Outer Bearing

Question

Question:

i am looking for a hub with a 1 1/4 inner bearing and a 3/4 outer bearing. 5 lug on 4 3/4. the outer bearing number is lm11949 and the inner bearing number is lm67048 and the seal is2.4 on outer dimension with a worn out 1.86 on the inner. a kit with these bearings calls for seal #15234 or 168238. i have 1 hub with nothing on it but a casting number that the bearings came off of and it is 38809.

asked by: Randall

0

Expert Reply:

With your hub having an inner bearing # LM67048 and outer bearing # LM11949, it sounds like you have an agricultural style hub, like the Redline Trailer Hub Assembly # AH15450ECOMP. However, this will have a 4 on 5 bolt pattern and this will be the only bolt pattern this hub is offered in, unfortunately.

With that being said, the best option we can recommend will be to replace your axle with something that uses more common parts. Though you will need to measure a few things, picture included, to make sure you get the correct axle, here are a few examples of what you would need.

The Dexter Trailer Axle Beam with EZ-Lube Spindles - 89" Long - 3,500 lbs # T3584F-EZ-8974 will measure 89 inches from hub face to hub face, and 74 inches from the center of one spring seat to the center of the other spring seat.

The Dexter Trailer Idler Hub Assembly for 3,500-lb E-Z Lube Axles - 5 on 4-3/4 # 845475UC1-EZ will then mate to this axle with the very common # L68149 and # L44649 bearings. With the 5 on 4 3/4 bolt pattern, there will also be no issues attaching your current wheels.

expert reply by: Lazer S

0

Needed Axle Measurements
(click to enlarge)

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 3

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 4

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 5

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 6

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 7

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 10

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 11

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Replacement 5 on 4 3/4 Hub With LM67048 Inner Bearing and LM11949 Outer Bearing

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching