Can Curt Base Plate Kit Attach to Roadmaster Sterling Tow Bar

Question

Question:

Can Curt Base Plate Kit for 2009 Honda CR-V Work with Roadmaster Sterling All Terrain Non-Binding Tow Bar?

asked by: Don

0

Expert Reply:

The Curt base plate kit part # C26KR could be used with a Roadmaster Sterling Tow Bar part # RM-576 but you'd have to use an adapter like the # BX88151 to make the connection.

expert reply by: Jameson C

0

Answer 1

We have exactly what you're needing with the Roadmaster Tow Bar to Blue Ox Brackets Adapter #RM-031. This is designed to work with a variety of Roadmaster tow bars, including your Falcon 5250, and makes them compatible with Blue Ox base plate…

view full answer...

Answer 2

You'll only need a single fuse bypass switch like the Curt Fuse Bypass Switch for Towed Vehicles #C93HR you were looking at. You'll want to pull the ACC Radio fuse, which is fuse #34 and the location can be seen in the attached picture. To…

view full answer...

Answer 3

The Roadmaster Tow Bar to Blue Ox Brackets Adapter #RM-031 referenced in your question is designed to adapt Roadmaster Blackhawk, Falcon or Sterling tow bars to Blue Ox Brackets. I went out to the warehouse and pulled one of the brackets so I could…

view full answer...

Answer 4

If you refer to the linked photo you'll see where bearing part numbers usually appear on such parts and this will help you with finding proper replacements. It is a very good idea to check the bearings and the grease seals on your 20-year-old tow…

view full answer...

Answer 5

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 6

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 7

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

The installation instructions for this product are recommended for individuals who have experience winding torsion springs. If you have not worked with a torsion spring system before, we recommend contacting a local garage door company to install…

view full answer...

Answer 10

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 11

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 12

Your trailer looks awesome! The Road armor equalizers #LC696740 and Equa-Flex Cushioned Equalizers #LC279687 are both pretty similar in performance even though the Road Armor has two dampers. The main difference is the size of the equalizers. The…

view full answer...

Can Curt Base Plate Kit Attach to Roadmaster Sterling Tow Bar

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching