Dimensions For Dutton-Lainson Worm Gear Hand Winch # DL11001

Question

Question:

What are the mesurments of the base and how tall is it? I did not find these specs on any of the web pages.

asked by: John

1

Helpful Expert Reply:

The dimensions for the Dutton-Lainson Worm Gear Hand Winch # DL11001 are as follows:

Height including hand crank: 12-1/4 inches
Length of side panel: 5-1/2 inches
Height of side panel: 4-1/4 inches
Width of base: 4-3/4 inches

expert reply by: Brandon M

1

click to enlarge

Answer 1

The type of manual winch I suggest for your car trailer is a worm gear type which prevents the car from rolling backwards even if you let go of the handle. Winch capacity for your application with a rolling load on an incline does not need be very…

view full answer...

Answer 2

The best type of hand winch for your car trailer application is a brake winch. These provide a self-locking holding action to prevent a runaway load. Their planetary gears deliver easy and efficient cranking. A good option is the Fulton High…

view full answer...

Answer 3

The only hand winches we offer that can have a drill attached to them for operation are worm gear winches like part #DL11001 which does have a hex drive and you can use a 5/8 inch socket attachment to power the load in or out.

view full answer...

Answer 4

To drive the hex drive of the Dutton-Lainson Hand Winch #DL11001 does not require a special tool to do so. What you need is just a 5/8 socket which you most likely already have and you'd be set.

view full answer...

Answer 5

If you are wanting to use a drill to ease operation of the winch, the Dutton-Lainson #DL11011 would be a much better choice. This winch is specifically designed so that the handle is easily removable for use with a drill. Using the shaft directly…

view full answer...

Answer 6

I do have a solution for you, however the Dutton-Lainson Hand Winch #DL11004 referenced in your question is actually designed for use with a polyester strap and not cable. For the Dutton-Lainson 2,000 pound hex gear hand winch that uses cable you…

view full answer...

Answer 7

The Dutton-Lainson Worm Gear Hand Winch, part #DL11001, is a single speed brake winch for use with cable. The brake function is when the cranking is stopped the reel automatically stops. It can be cranked in reverse. There is no free wheel mode, so…

view full answer...

Answer 8

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 11

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 12

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Dimensions For Dutton-Lainson Worm Gear Hand Winch # DL11001

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching