Can I Install Only 1 Water Heater Power Switch for Gas and Electric Water Heater

Question

Question:

can I install both electric and the gas wires to the same pin ? at the same time/ Thanks

asked by: GEORGE D

1

Helpful Expert Reply:

You won't want to wire both functions to a single switch like the Replacement Single-Panel On/Off Switch for Atwood Gas and Electric Water Heaters - Black # AT91959 since it wouldn't allow for proper functioning. You would want to wire each power source for your water heater to a switch like the # AT91959 or the Replacement Double-Panel On/Off Switch for Dometic Gas / Electric Combination Water Heaters - White # AT91230.

expert reply by: Erik B

1

Answer 1

I am attaching a wiring diagram for the Replacement Single-Panel On/Off Switch for Atwood Gas and Electric Water Heaters #AT91959 that you can reference.

view full answer...

Answer 2

The only way I can recommend you wire up the Atwood Switch part #AT91959 is by using the attached diagram which means using a 12 volt power source. I don't have a way we can recommend using a 110.

view full answer...

Answer 3

There are many variables when installing the Double-Panel On/Off Switch for Dometic Gas / Electric Combination Water Heaters part #AT91230 therefore it is best to match the wire to the terminals using its function, not the color. The reason for this…

view full answer...

Answer 4

Since you don't have the wiring harness on your previous RV water heater you most likely had an all propane powered unit. The Atwood RV Water Heater w/ Heat Exchange - Gas and Electric - Automatic Pilot - 8,800 Btu - 6 Gal #AT96163 is powered by…

view full answer...

Answer 5

We do not have any way to know where an individual switch is located on a trailer; the best we can do is offer a replacement switch. For a single-panel switch you would need the Replacement Single-Panel On/Off Switch for Atwood Gas and Electric Water…

view full answer...

Answer 6

I reached out to my contact at Dometic and he agreed that your switch needs to be replaced. You can use one of the following: Dual Switch White - #AT91230 Single Switch White - #AT91859 Black - #AT91959 Attached is a photo showing the wiring…

view full answer...

Answer 7

There's a wiring diagram in the install instructions for the Dometic RV Water Heater part #DMC74FR that I attached to this page. I don't have a way to verify what the wires of your RV are that ran to your old water heater though. We do have…

view full answer...

Answer 8

I attached a diagram that shows how the Atwood switch part #AT91959 that you referenced gets wired. You will need to use the diagram on the bottom of the picture for your GC6AA-9E.

view full answer...

Answer 9

I am not sure what the different wires on your Jayco Jay Flight 2077BHS are connected to but from my understanding the new water heater should be configured as follows: Blue - Lock Out Lamp Green - Ground Orange - Gas Control White - Electric Control…

view full answer...

Answer 10

I attached a diagram that shows how the Atwood switch part #AT91959 wires up. There are three sets of wiring diagrams that you will need to compare to the water heater you have now to determine which is correct.

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Can I Install Only 1 Water Heater Power Switch for Gas and Electric Water Heater

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching