Replacement Parts for Balcrank 16030 Surge Brake Actuator

Question

Question:

Im searching for brake parts for my trailer. In particular a new coupler, master cylinder and brake hardware if available. Ive searched the model number with no success. If you have any parts available or suggestions I would appreciate any help you could offer. Thank you for your time.

asked by: Ryan A

0

Expert Reply:

Thank you for the photos. It looks like you've got an older version of the Toledo Actuator - 2-5/16" Bulldog Coupler - 6,000 lbs. # 16039, which would make sense since the tag says 16030. The available replacement parts for this series of actuators are the Replacement Shock Absorber for Toledo Brake Actuators # 1844-2 and the Replacement Master Cylinder for Toledo Drum Brake Actuators # 10614.

If you can let me know what brake hardware you need- mounting hardware, etc., and the size of the brakes I can help you locate parts for that as well.

expert reply by: Erik B

0

Answer 1

To replace your surge brakes there are a few things you'll need to know, the first being if you have drum or disc brakes. You can then choose the correct disc or drum brake assembly; you'll need to know your axle capacity and wheel…

view full answer...

Answer 2

Indeed they are; you can use the same replacement shock absorber and master cylinder for your Balcrank Actuator 16030, which are the following parts: - Replacement Master Cylinder for Toledo Drum Brake Actuators #10614 - Replacement Shock Absorber…

view full answer...

Answer 3

We have a few different parts for Toledo actuators but not a master cylinder rebuild kit. We have the master cylinder that you referenced, #10614. We also have a replacement shock, #1844-2, a pivot bushing, #1745, and a pivot shaft, #1829. If your…

view full answer...

Answer 4

The thread size is 3/8"-24 but the fitting size is 3/16". This standard for trailer brake lines. This will go from 1/2 inch thread size to 3/8 inch. If the dimensions you took are 1/2 inch and 3/8 inch of the threads this will fit.

view full answer...

Answer 5

The part you are looking for is the Brass Connector for Titan Disc Brake Kit, #T4750300. This is the fitting that threads into the master cylinder that accepts the reverse lockout solenoid on your Titan actuator. I have attached a link to this part…

view full answer...

Answer 6

If you are talking about the small opening on the outside and inside of the Orifice Connector #T1209800 then those measure 0.0010" and 0.0865" respectfully. I went out to the warehouse and measured them with the digital caliper. Please note…

view full answer...

Answer 7

Look at the side of the master cylinder and you'll be able to tell which type of brakes it is designed for by the number. If you see 23744 stamped into the side of it you have a drum brake model. If you have 25744 stamped in the side it's for…

view full answer...

Answer 8

We do have the Titan master cylinder replacement part #DX66FR which has the number 23744 stamped on the side of it. See attached picture. A lock out solenoid would attach directly to the back of the master cylinder without an adapter. If you are in…

view full answer...

Answer 9

The Replacement Master Cylinder #10614 will fit Balcrank T-6 actuators for drum brakes. You will need to reuse your existing mounting hardware.

view full answer...

Answer 10

When greasing or re-packing the bearings with grease, you need to fill every space of the bearing with grease. This can be done either by hand, by using a bearing packer #L70025, or if you plan on servicing multiple trailers, or just want to cut down…

view full answer...

Replacement Parts for Balcrank 16030 Surge Brake Actuator

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching