What are the Torque Ratings for a Hitch Installed on a 2008 Toyota Highlander

Question

Question:

I need to check the torque requirements for a Toyota highlander 2inch ball hitch that I installed 6 YEARS AGO - WHAT is the torque for this hitch

asked by: Frank M

0

Expert Reply:

Though it will depend on the hitch you have installed, all of the M10 bolts for the Draw-Tite # 75726 and 75586 should be torqued to 42 lb-ft. The Curt # 13534, which also uses M10 bolts, should be torqued to 48 lb-ft. If you installed an EcoHitch, like # 306-X7137, the M10 bolts should be torqued to 60 lb-ft.

This should be checked every now and then to make sure everything is secure. I generally recommend doing so at the beginning and end of the towing season.

expert reply by: Lazer S

0

Answer 1

If your 2008 Toyota Highlander has a converter box under the dashboard already then you have the factory tow package. To give you an idea of what to look for I've attached a video of the trailer wiring being installed onto a Highlander…

view full answer...

Answer 2

The best trailer hitch we have for clearance on your 2013 Toyota Highlander is the EcoHitch Hidden Trailer Hitch Receiver #306-X7137 as it has a crosstube that sits behind the bumper so the only part below the bumper is the 2" hitch…

view full answer...

Answer 3

That is quite the price for a brake controller installation. I would think a local mechanic could get the job done at a lower price. To install a brake controller in your 2011 Hybrid Toyota Highlander, you will want a wiring harness and our…

view full answer...

Answer 4

Since the bolts that go into the frame of your 2017 GMC Terrain to mount the etrailer Trailer Hitch Receiver #e98865 are getting stuck half way I recommend using some spray lubricant like WD-40 and the Nylon Tube Brush - 1/2" #814092 to…

view full answer...

Answer 5

I recommend our etrailer Trailer Hitch Receiver #e38KR for your 2024 Kia Sportage Hybrid. Our receiver has a hidden cross tube and matte black finish which provides for a clean factory appearance. You will want to use the Curt Custom Fit Wiring…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

The rear spare tire does not need to be lowered or removed in order to install the Curt Trailer Hitch Receiver part #13575 on a 2014 Mazda CX-9. The installation is very simple, simply lift the hitch up into position and tighten the hardware then…

view full answer...

Answer 8

We do have a video of a similar product on a 2010 Mazda CX-7. I have linked to it below. It is a bit easier than the install on a 2008 CX-9. For your vehicle, You would need to connect to both the driver and passenger side tail light. You would…

view full answer...

Answer 9

Not all aluminum trailer frames are strong enough for use with a steel weight distribution (WD) system. It is possible that the stronger steel WD components could put too much stress on the frame. If your trailer has an aluminum frame you'll…

view full answer...

Answer 10

The 2013 Mazda CX-9 wasn't factory prewired for a brake controller, so you'll need to hardwire the controller. The installation isn't too difficult, I'll provide some videos and help articles that will help you through the process.…

view full answer...

Answer 11

The Curt hitch part #13575 when installed does change the spare tire access but you still will be able to access the spare tire when needed. Basically you'll have to push the spare around the hitch as you raise or lower it. We've had…

view full answer...

Answer 12

The best way to determine if your 2012 Toyota Highlander has a factory tow package is to have a Toyota dealer run the VIN number in their computer system. They can tell you how the vehicle is equipped that way. If they say you do not have the tow…

view full answer...

What are the Torque Ratings for a Hitch Installed on a 2008 Toyota Highlander

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching