Fit of Curt C56370 Trailer Wiring Harness on FWD Model 2020 Honda CR-V

Question

Question:

I purchased the 56370 but I am concerned on the package it states Honda CR-V excluding FWD 17-18. It this the correct harness for my 2020 FWD?

asked by: Rick K

0

Expert Reply:

For the 2020 Honda CR-V, the Curt # C56370 is only a fit for AWD vehicles. For a 2020 Honda CR-V front wheel drive model, you'd want to use # 118741 which is a fit for all 2020 CR-V models.

You can see an install video by clicking the provided link.

expert reply by: Mike L

0

Answer 1

We can definitely help you find what you need. Typically the wiring harness you need will depend on the trailer and whether or not it has brakes. In most cases the small trailers you've mentioned will have 4 pin trailer connectors and typically…

view full answer...

Answer 2

I verified that the Curt wiring harness part #C56370 will fit your front wheel drive 2017 Honda CR-V. In terms of trailer wiring there is no difference between AWD and FWD.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

There are indeed two 2" trailer hitches available for your 2020 Honda CR-V; the etrailer #e98848 and the Curt #C13397. These Class III hitches are essentially identical in every way except for the finish/powder coat that they use. I personally…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 8

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 9

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Fit of Curt C56370 Trailer Wiring Harness on FWD Model 2020 Honda CR-V

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching