Compatibility of Pop and Lock # PAL5500 with OEM Back-Up Camera on 2010 Toyota Tacoma

Question

Question:

Does the Back Up Camera on a 2010 Tacoma Mount in the Pop and Lock Custom Locking Tailgate Handle. My 2010 Tacomas camera is on the opposite side of handle facing the tailgate it will be on my rightside of the of the PAL5500 camera slot which appears to be on left side of handle. will the wires for the camera reach the opposite side? and mount ok?

asked by: Felix R

0

Expert Reply:

According to Pop and Lock, the back-up camera in your 2010 Tacoma is indeed compatible with the # PAL5500 locking tailgate handle. There will be enough slack in the wiring to move the camera from its existing location on the OE tailgate handle to the left side of the Pop and Lock # PAL5500.

expert reply by: Mike L

0

Answer 1

For a manual tail gate lock for your 2013 Toyota Tacoma with the backup camera you can use #PAL5400. I have included a picture that shows where the camera will mount on the new lock. I have also included a link to a video review of this lock for…

view full answer...

Answer 2

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the…

view full answer...

Answer 3

The Rhino Rack ROC25 part #RR46XR has a 165 lb dynamic weight capacity which means that's how much it can carry while travelling and incurring the standard bumps and movement that creates. While Rhino Rack doesn't give a static weight…

view full answer...

Answer 4

I reached out to Timbren, who told me the the actual jounce springs are both the same height at 3-3/4 inches, but the bracket height is different. So there aren't shorter springs, and the correct fit for your 2019 Toyota Tacoma 4WD is going to…

view full answer...

Answer 5

Pop and Lock does have the manual locking tailgate handle, #PAL5500, that will work with your 2015 Toyota Tacoma with backup camera. You can turn it into a power locking handle by adding conversion kit #PAL8525.

view full answer...

Answer 6

The Pop & Lock Custom Tailgate Handle with Lock #PAL5400 that you referenced is confirmed as a fit for all models of the 2005 Toyota Tacoma so it would work well for you. This one will key to your truck door key so that the same key will open the…

view full answer...

Answer 7

I spoke with my contact at Pop and Lock and he told me the #PAL5500 will work for you. Here is what he emailed me: The reason the cylinder is on the opposite side is because this was our older model #PAL5300. Yes the #PAL5500 will fit this vehicle.

view full answer...

Answer 8

For your 2010 Toyota Tacoma Quad Cab, I would recommend using the Pop and Lock Custom Locking Tailgate Handle, #PAL5500. This tailgate lock includes a slot for the backup camera and is designed to give a factory look.

view full answer...

Answer 9

The correct Pop and Lock tailgate lock for your 2013 Toyota Tacoma with a backup camera is the part #PAL5400 which comes with a lock cylinder that will allow you to key to your truck's key. I attached an install video for this for you to check…

view full answer...

Answer 10

The Pop & Lock Custom Locking Tailgate Handle #PAL5500 that you referenced allows you to relocate the backup camera of the 2015 Tacoma to a new locking handle. It does not replace the backup camera so the quality of the camera does not change.

view full answer...

Answer 11

You can use the Custom Locking Tailgate Handle, #PAL5500, with the back up camera on your 2010 Toyota Tacoma. The camera will insert in the slot on the back of the tailgate handle and a small plastic piece will need to be removed from the bottom of…

view full answer...