Will the Curt T- Connector C56040 Fit on a 2021 Subaru Outback Wagon XT

Question

Question:

Will this 4 flat connector/ harness work on the 2021 Outback XT ? I was told by the dealer that the ‘21 wiring was changed from the ‘20. Thanks

asked by: Jan

0

Expert Reply:

Yes. The Curt # C56040 is a confirmed fit for your 2021 Subaru Outback Wagon XT; we've even got a video of the installation for you that shows this harness being installed on a 2021 model. I've linked that video to this answer for you to have a look at.

expert reply by: Erik B

0

Answer 1

There is absolutely no drilling at all needed to install the Curt Trailer Hitch Receiver #C67JR on your 2020 Subaru Outback; installing the hitch will use a combination of your Subaru's existing hardware and the included bolts. In regards to…

view full answer...

Answer 2

For your 2021 Subaru Outback I recommend the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector #C56040 which will plug into the factory connector in the rear cargo area of your vehicle, and is definitely something you can…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 6

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 12

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Will the Curt T- Connector C56040 Fit on a 2021 Subaru Outback Wagon XT

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching