Where is the Brake Controller Adapter Plug In on a 2020 Nissan Pathfinder

Question

Question:

I followed the video for the 2019 Nissan Pathfinder to install the wire harness for my break controller and did not see the plug. Did it move on the 2020?

asked by: Kevin W

0

Expert Reply:

The brake controller adapter plug can be found by checking near the parking brake pedal for a main harness; you'll follow that main harness up and look for an offshoot (sub harness) of the main harness, doubled up and taped to the main harness about half way up behind the dash. You may want to remove the fuse box cap to get a glimpse at it. The cap is white with no wires coming out of the top and held by fabric black tape.

There is a cap that has to be removed, which you'll just press the lock to the cap and remove; you can then plug in the # 3050-P adapter and complete the installation of your brake controller.

expert reply by: Erik B

0

Answer 1

Installing a brake controller on your 2023 Nissan Frontier will require a 7-way along with the brake controller itself. Since you do not have the factory trailer connector you will need the Curt T-Connector Vehicle Wiring Harness #C56226. This…

view full answer...

Answer 2

All 2020 Nissan Pathfinders come from the factory prewired for a brake controller and a 7-way trailer connector, though it might lack the 7-way and the relays needed to activate the tow package. You will need a brake controller. If your vehicle…

view full answer...

Answer 3

From what I can find on the 2022 Nissan Frontier, the plug for the brake controller that will let you use a harness like the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers #3050-P is located just above the OBD connector, taped tight…

view full answer...

Answer 4

To install the Prodigy P3 Trailer Brake Controller #90195 in your 2019 Nissan Pathfinder you can find the brake controller port directly under the dash as in the accompanying photo. This will allow you to plug in the Tekonsha Plug-In Wiring Adapter…

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 10

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 11

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 12

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Where is the Brake Controller Adapter Plug In on a 2020 Nissan Pathfinder

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching