Trailer Hitch Installation Instructions and Difficulty on a 2010 Volvo XC70 Wagon
Question:
On a scale of 1-10, how hard is it to install this hitch assembly at home with basic tools? What is actually involve? Where does the assembly bolt into? No holes need to be drilled, correct? Does anything need to be removed to get access to the install area?
asked by: Kevin
Expert Reply:
The way that we rate installation is by how long it takes from start to finish to install the trailer hitch. For Draw-Tite trailer hitch # 75916 we estimated that it will take at least 100 minutes to install it on a 2010 Volvo XC70. This gives it an 10 out of 10 difficulty rating and is on the liberal side meaning that it will probably take longer unless you are an experienced hitch installer.
There is no drilling required but there is fascia trimming required and the rear fascia also has to be temporarily removed. I have included a link to the installation instructions for you to view. All of the hitches for your vehicle will require trimming and fascia removal.
If you plan on doing some towing I recommend the etrailer ball mount kit # 989900. It comes with 2 ball mounts, 2 balls, a hitch pin with clip, and a storage bag. For trailer wiring use # C59496. I have included a video and instructions for the wiring as well.
Products Referenced in This Question
etrailer Ball Mount Kit for 2" Hitches - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- 1-7/8 Inch Ball
- 2 Inch Ball
- Two Balls
- Steel Ball
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Drop - 4 Inch
- Rise - 1 Inch
- Rise - 3 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- Ball Mount Kit
- etrailer
more information >
Curt Powered Tail Light Converter w/ 4-Way Flat Trailer Connector and Install Kit
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Converter
- 8 Feet Long
- Universal Fit
- 4 Flat
- CURT
more information >
Product Page this Question was Asked From
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 400 lbs TW
- 4000 lbs GTW
- 2 Inch Hitch
- Concealed Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Trailer Hitch
- Shop: Tekonsha Powered Tail Light Converter w/ 4-Way Flat Trailer Connector and Install Kit
- Shop: etrailer Ball Mount Kit for 2" Hitches - 7,500 lbs
- Shop: T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Trailer Wiring
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Search Results: 44649
- Article: How to Choose the Right Trailer Hitch Class
- Video: Choosing the Right Trailer Wiring
- Shop: 7- and 4-Pole Trailer Connector Socket w/ Mounting Bracket - Vehicle End
- Video: Choosing the Right Brake Controller
- Q&A: Wiring a Camper Shell Third Brake Light on a 2017 Chevrolet Silverado
- Search Results: 68149
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: Lippert Solera Slider Slide-Topper Review
- Article: Trailer Wiring Diagrams
- Shop: Brake Controller
- Search Results: 25580
- Q&A: 10k Dexter Replacement Hub for a 8-415
- Search Results: dust cap
- Q&A: How to Determine if Trailer Axle is Not Aligned and How to Measure to Replace Trailer Axle
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)
- Shop: Fifth Wheel Hitch
- Article: My Trailer Hitch Doesn't Fit
- Search Results: dust caps
- Q&A: Replacement Hub Needed for Lippert 122093 Hub on 5,200 lbs Axle
- Shop: Gooseneck Hitch