Are There Replacement Keys for Tow Ready Hitch Locks

Question

Question:

I have the above hitch lock but need an extra set of keys. The key code is L825. Do you sell these? Thanks,

asked by: Joel J

1

Helpful Expert Reply:

I do have an option for you but there are no replacement keys available for Curt products like the Trailer Hitch Receiver Lock part # C23519. I suggest the etrailer Hitch Receiver Lock part # e98881 which we do offer replacement keys for if needed.

expert reply by: Conner L

1

Answer 1

The Trailers Hitch Receiver Lock #C23519 is made by Curt, and unfortunately there are no replacement keys available for this product. Instead, I recommend using the etrailer Hitch Receiver Lock #e98881, which has replacement keys available if…

view full answer...

Answer 2

You can identify your key code by inspecting the face of the lock core for a numeric code, or you can look at the key itself. If you're in the market for a new hitch receiver lock, the etrailer Hitch Receiver Lock for 2" and 2-1/2"…

view full answer...

Answer 3

For the hitch lock part #e98881 to get the correct replacement key you will need to locate your current key number. The key number is located on the lock core and should be three numbers that begin with a zero. If you can't locate the key number,…

view full answer...

Answer 4

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 7

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 8

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 9

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

On a single axle trailer you will want to have a hanger spacing of around 22-3/4 inches when using the 23-1/8 inch long Double-Eye Spring #e59SR. This will allow that rear shackle to correctly lean away from the axle for proper suspension travel.

view full answer...

Answer 12

On single axle trailers typically you put the hanger spacing right at 1/4 of an inch shorter than the leaf spring length from eye to eye center. So if you were using the leaf spring part #e54SR that you referenced which measures 25-1/8 inches long…

view full answer...

Are There Replacement Keys for Tow Ready Hitch Locks

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching