Velcro Replacement for Truxedo Truxport Tonneau Cover

Question

Question:

2010 ford f 150 short box Truxport cover. The Velcro is 1 inch wide. Do you sell that size?

asked by: Trace D

0

Expert Reply:

For your Truxedo Truxport tonneau cover the correct velcro you need for the side rails is the part # TX1117876 and you'd be set. This comes with screws to install and would need to be cut down to the size you need.

expert reply by: Jameson C

0

Answer 1

The Replacement TruXedo Shur-Bond Hook-And-Loop Fastener for your TruXsport cover on your Toyota Tundra is 80 inches long and 1 inch wide. It is part #TX1117876.

view full answer...

Answer 2

For your Truxedo Truxport tonneau cover the correct velcro you need for the side rails is the part #TX1117876 and you'd be set. This comes with screws to install and would need to be cut down to the size you need.

view full answer...

Answer 3

We have Truxedo replacement Shur-Bond Velcro strips that are 1 inch wide with the part #TX1117877 which seems to be a better match for what you are in need of since you said you have 1 inch wide Velcro now and the strips you mentioned are 1-1/4…

view full answer...

Answer 4

The Replacement Truxedo Shur-Bond Velcro Brand Fastener, part #TX1117876 is designed to work with TruxSport tonneau covers only. From the photo you sent it looks like you have a Lo Pro tonneau cover on your truck. The correct replacement Velcro for…

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 9

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 12

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Velcro Replacement for Truxedo Truxport Tonneau Cover

Product Page this Question was Asked From

Continue Researching